- 您現在的位置：買賣IC網 > PDF目錄9801 > DS1852B-000+T&R (Maxim Integrated Products)IC MONITOR TXRX OPTICAL 25-BGA PDF資料下載
參數資料
| 型號： | DS1852B-000+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 25/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MONITOR TXRX OPTICAL 25-BGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 收發器 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 25-TFBGA，CSPBGA |
| 供應商設備封裝： | 25-BGA（5x5） |
| 包裝： | 帶卷 (TR) |
DS1852
8 of 26
DIGITAL INPUTS
The four digital inputs (Din, RSin, Fin, and Lin) can be read through the 2-wire bus. The logic levels at
these inputs are mirrored in the “l(fā)ogic states” byte (6Eh) in Table 00h.
2-WIRE OPERATION
Clock and Data Transitions
The SDA pin is normally pulled high with an external resistor or device. Data on the SDA pin may only
change during SCL low time periods. Data changes during SCL high periods will indicate a start or stop
conditions depending on the conditions discussed below. See Figure 2 for further details.
Start Condition
A high-to-low transition of SDA with SCL high is a start condition that must precede any other
command. See Figure 2 for further details.
Stop Condition
A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop
command places the DS1852 into a low-power mode. See Figure 2 for further details.
Acknowledge Bit
All address bytes and data bytes are transmitted through a serial protocol. The DS1852 pulls SDA low
during the ninth clock pulse to acknowledge that it has received each word.
Standby Mode
The DS1852 features a low-power mode that is automatically enabled after power-on, after a stop
command, and after the completion of all internal operations.
2-Wire Interface Reset
After any interruption in protocol, power loss, or system reset, the following steps reset the DS1852:
1) Clock up to nine cycles.
2) Look for SDA high in each cycle while SCL is high.
3) Create a start condition while SDA is high.
Device Addressing
The DS1852 must receive an 8-bit device address word following a start condition to enable a specific
device for a read or write operation. The address word is clocked into the DS1852 MSB to LSB. The
address word defaults to A0h then the R/W (READ/WRITE) bit when ASEL is a logic zero. If the R/W
bit is high, a read operation is initiated. If R/W is low, a write operation is initiated. The device address
is changed to the internal chip address (Table 03h address D0h) when ASEL is logic one. The default
internal chip address from the factory is A2h.
相關PDF資料 |
PDF描述 |
|---|---|
| V150C12M150B | CONVERTER MOD DC/DC 12V 150W |
| VI-232-IU-F2 | CONVERTER MOD DC/DC 15V 200W |
| MAX9113ESA+T | IC LINE RCVR LVDS DUAL 8SOIC |
| V150B5M150BG3 | CONVERTER MOD DC/DC 5V 150W |
| VI-232-IU-F1 | CONVERTER MOD DC/DC 15V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1852B-00C+ | 功能描述:模數轉換器 - ADC Optical Transceiver Diagnostic Monitor RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| DS1852B-00C+T&R | 制造商:Maxim Integrated Products 功能描述:OPT TRANS DIAG MON REV C1 T&R LF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MONITOR TXRX OPTICAL 25-BGA 制造商:Maxim Integrated Products 功能描述:Data Converter ICs - Various Optical Transceiver Diagnostic Monitor |
| DS1852B-00C+T&R | 功能描述:模數轉換器 - ADC Optical Transceiver Diagnostic Monitor RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| DS1854 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual Temperature-Controlled Resistors with Two Monitors |
| DS1854B-050 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。