Temperature-Controlled, NV, I2C, Logarithmic Resistor 12 ________________" />
參數資料
型號: DS1841N+
廠商: Maxim Integrated Products
文件頁數: 4/17頁
文件大?。?/td> 0K
描述: IC RES LOG NV I2C 5.5V 10-TDFN
標準包裝: 368
接片: 128
電阻(歐姆): 22k
電路數: 1
溫度系數: 標準值 250 ppm/°C
存儲器類型: 非易失
接口: I²C,2 線串口
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 100°C
安裝類型: 表面貼裝
封裝/外殼: 10-WFDFN 裸露焊盤
供應商設備封裝: 10-TDFN-EP(3x3)
包裝: 管件
DS1841
Temperature-Controlled, NV, I2C,
Logarithmic Resistor
12
______________________________________________________________________________________
Register 0Ah: Control Register 2 (CR2)
FACTORY DEFAULT
00h
MEMORY TYPE
Volatile
0Ah
Reserved
Wiper
Access
Control
LUTAR Mode
Reserved
Bit 7
Bit 0
Bits 7 to 3
Reserved.
Bit 2
Wiper Access Control This bit is valid only in LUT Mode and in LUT Adder Mode.
0 = (Default) WR is loaded with the value from IVR summed with LUTVAL, or just the value of LUTVAL
based on the state of the Adder Mode bit.
1 = The DS1841 is placed in a manual mode, allowing WR (address 09h) to be programmed using I2C
commands.
Bit 1
LUTAR Mode This bit is valid only in LUT Mode and in LUT Adder Mode.
0 = (Default) The LUTAR value, located in at address 08h, is calculated following each temperature
conversion that points to the corresponding location in the LUT.
1 = Automatic updates of LUTAR are disabled, allowing the LUTAR register to be programmed using I2C
commands.
Bit 0
Reserved. This bit must be set to a 0.
Control Register 2 controls how the wiper position is determined.
Register 0Ch: Temperature Result (TEMP)
FACTORY DEFAULT
None
MEMORY TYPE
Volatile
0Ch
Sign
26
25
24
23
22
21
20
Bit 7
Bit 0
This register holds the current temperature result. It is updated every conversion time, tFRAME. To calculate the
temperature, treat the two’s complement binary value as an unsigned binary number, then convert it to decimal. If the
result is greater than or equal to 128, subtract 256 from the result. This register is only updated when the Update Mode
bit = 1. When the Update Mode bit = 0, no ADC updates are made to this register.
Register 0Eh: Supply Voltage Result (VOLTAGE)
FACTORY DEFAULT
None
MEMORY TYPE
Volatile
0Eh
Supply Voltage
Bit 7
Bit 0
This register holds the current supply voltage result. It is updated every conversion time, tFRAME. See the Supply Voltage
Monitoring section. This register is only updated when the Update Mode bit = 1. When the Update Mode bit = 0, no ADC
updates are made to this register.
相關PDF資料
PDF描述
DS1844S-100/T&R IC POT DIG QUAD 100K 20-SOIC
DS1845E-100/T&R IC POT/MEM DUAL NV 100K 14-TSSOP
DS1846E-010+T&R IC NV TRI-POT MEM MON 20TSSOP
DS1847E-010/T&R IC RES TEMP-CNTRL 10/10K 14TSSOP
DS1848B-C10+ IC RES/MEM TEMP 10/10K 16-CSBGA
相關代理商/技術參數
參數描述
DS1841N+ 功能描述:數字電位計 IC Temp-Cntrlld NV I2C Logarithmic Resistor RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1841N+T&R 制造商:Maxim Integrated Products 功能描述:TEMP-CNTRLD, NV, I2C, LOGARITHMIC RES - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC RES LOG NV I2C 10-TDFN
DS1841N+T&R 功能描述:數字電位計 IC Temp-Cntrlld NV I2C Logarithmic Resistor RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1841T+ 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Temperature-Controlled, NV, I2C, Logarithmic Resistor
DS1841T+T&R 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Temperature-Controlled, NV, I2C, Logarithmic Resistor