- 您現在的位置：買賣IC網 > PDF目錄376962 > DS1830A Reset Sequence Pushbutton PDF資料下載
參數資料
| 型號： | DS1830A |
| 英文描述： | Reset Sequence Pushbutton |
| 文件頁數： | 3/7頁 |
| 文件大小： | 276K |
| 代理商： | DS1830A |
D1830/A
3 of 7
OPERATION — PUSHBUTTON RESET
The DS1830 provides a pushbutton switch for manual reset control. When any of the DS1830/A resets
are not active (low) a reset cycle can be initiated by a pushbutton reset. The pushbutton reset is generated
by pulling the PBRST pin low for at least 1ms. When the push- button is held low all resets are forced
active. The reset will remain active until the pushbutton input is released and then will start a sequenced
time-out based on the condition of the TD input. The Pushbutton input is pulled high through an internal
40k pull-up resistor and debounced via internal circuitry. See Figure 2 for an application example and
Figure 3 for the timing diagram.
PUSHBUTTON RESET
Figure 2
TIMING DIAGRAM — PUSHBUTTON RESET
Figure 3
OPERATION — TIME DELAY SELECT
The DS1830 provides an input to select three time delay characteristics for the reset outputs. The TD
input has 3 states high (V
CC
), low (ground) and no connect (N.C.). Table 2 details the minimum timing
based on the state of the TD input. If the TD input is connected to ground;
RST1
will have a minimum
time delay of 10 ms after V
CC
is in tolerance. If the TD input is floated;
RST1
will have a minimum time
delay of 20 ms after V
CC
is in tolerance. If the TD input is connected to V
CC
,
RST1
will have a minimum
time delay of 50 ms after V
CC
is in tolerance. An oscillator and clock chain generate the reset timing with
each time delay based on the same device oscillator. The time delay for
RST2
will be 5 times as long as
RST1
and
RST3
will be 10 times the duration of
RST1
.
TD CONTROL MINIMUM RESET TIMING
Table 2
TD
T
RST1
TD = GND
10ms
TD = N.C.
20ms
TD = V
CC
50ms
T
RST2
50ms
100ms
250ms
T
RST3
100ms
200ms
500ms
相關PDF資料 |
PDF描述 |
|---|---|
| DS1830AS | Reset Sequence Pushbutton |
| DS1830AU | Reset Sequence Pushbutton |
| DS1830U | Reset Sequence Pushbutton |
| DS1830S | Reset Sequence Pushbutton |
| DS1834A | Dual EconoReset with Pushbutton |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1830A+ | 功能描述:監控電路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1830AS | 功能描述:監控電路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1830AS/T&R | 制造商:Maxim Integrated Products 功能描述:3.3V RESET SEQUENCER 8P SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC SEQUENCER RESET PB 3.3V 8SOIC 制造商:Maxim Integrated Products 功能描述:Supervisory Circuits Reset Sequencer |
| DS1830AS/T&R | 功能描述:監控電路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1830AS+ | 功能描述:監控電路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。