- 您現在的位置：買賣IC網 > PDF目錄97865 > DS1822/T&R (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | DS1822/T&R |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| 封裝： | TO92-3 |
| 文件頁數： | 21/21頁 |
| 文件大?。?/td> | 222K |
| 代理商： | DS1822/T&R |
DS1822
9 of 21
is available in Application Note 27 entitled Understanding and Using Cyclic Redundancy Checks with
Dallas Semiconductor Touch Memory Products.
CRC GENERATOR Figure 9
1-WIRE BUS SYSTEM
The 1-Wire bus system uses a single bus master to control one or more slave devices. The DS1822 is
always a slave. When there is only one slave on the bus, the system is referred to as a “single-drop”
system; the system is “multidrop” if there are multiple slaves on the bus.
All data and commands are transmitted least significant bit first over the 1-Wire bus.
The following discussion of the 1-Wire bus system is broken down into three topics: hardware
configuration, transaction sequence, and 1-Wire signaling (signal types and timing).
HARDWARE CONFIGURATION
The 1-Wire bus has by definition only a single data line. Each device (master or slave) interfaces to the
data line via an open drain or 3-state port. This allows each device to “release” the data line when the
device is not transmitting data so the bus is available for use by another device. The 1-Wire port of the
DS1822 (the DQ pin) is open drain with an internal circuit equivalent to that shown in Figure 10.
The 1-Wire bus requires an external pullup resistor of approximately 5 k
Ω; thus, the idle state for the 1-
Wire bus is high. If for any reason a transaction needs to be suspended, the bus MUST be left in the idle
state if the transaction is to resume. Infinite recovery time can occur between bits so long as the 1-Wire
bus is in the inactive (high) state during the recovery period. If the bus is held low for more than 480
μs,
all components on the bus will be reset.
HARDWARE CONFIGURATION Figure 10
(MSB)
(LSB)
XOR
INPUT
VPU
4.7k
5μA
Typ.
RX
TX
DS1822 1-WIRE PORT
100
Ω
MOSFET
TX
RX
RX = RECEIVE
TX = TRANSMIT
1-wire Bus
DQ
Pin
相關PDF資料 |
PDF描述 |
|---|---|
| DS1822 | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822+T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822Z | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS18B20-PAR/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, ROUND, THROUGH HOLE MOUNT |
| DS18B20-PAR | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, ROUND, THROUGH HOLE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1822-W | 制造商:Maxim Integrated Products 功能描述:1-WIRE DIGITAL THERMOMETER SOIC - Rail/Tube |
| DS1822Z | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1822Z/T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Econo 1-Wire Digital Thermometer |
| DS1822Z/T&R | 制造商:Maxim Integrated Products 功能描述:1-WIRE DIGITAL THERMOMETER SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER ECONO DIG 8-SOIC |
| DS1822Z/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。