- 您現在的位置：買賣IC網 > PDF目錄97865 > DS1821S+ (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | DS1821S+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | 0.208 INCH, LEAD FREE, SOIC-8 |
| 文件頁數： | 2/20頁 |
| 文件大?。?/td> | 543K |
| 代理商： | DS1821S+ |
DS1821
10 of 18
INITIALIZATION
All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence
consists of a reset pulse transmitted by the bus master followed by a presence pulse transmitted by the
DS1821.
The presence pulse lets the bus master know that the DS1821 is on the bus and ready to
operate. Timing for the reset and presence pulses is detailed in the 1-Wire SIGNALING section.
DS1821 FUNCTION COMMANDS
The DS1821 function commands in this section allow the master to communicate with and configure the
DS1821. The DS1821 function commands are summarized in Table 4.
READ TEMPERATURE [AAh]
Provides read access to the 1-byte temperature register.
START CONVERT T [EEh]
Initiates temperature conversions. If the part is in one-shot mode (1SHOT = 1), only one conversion will
be performed. If it is in continuous mode (1SHOT = 0), continuous conversions will be performed until a
Stop Convert T command is received.
STOP CONVERT T [22h]
Stops temperature conversions when the device is in continuous conversion mode (1SHOT = 0). This
opcode has no function if the device is in one-shot mode (1SHOT = 1).
WRITE TH [01h]
WRITE TL [02h]
Provides write access to the 8-bit TH and TL registers, respectively.
READ TH [A1h]
READ TL [A2h]
Provides read access to the 8-bit TH and TL registers, respectively.
WRITE STATUS [0Ch]
Provides write access to the 8-bit status/configuration register.
READ STATUS [ACh]
Provides read access to the 8-bit status/configuration register.
READ COUNTER [A0h]
Provides read access to data in the 9-bit counter register for use in high-resolution temperature
calculations. This is explained in detail in the HIGH-RESOLUTION TEMPERATURE READINGS
section.
LOAD COUNTER [41h]
Loads the 9-bit data from the slope accumulator register into the counter register so that it can be accessed
using the Read Counter [A0h] command. Use of the Load Counter command is explained in detail in the
HIGH-RESOLUTION TEMPERATURE READINGS section.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1821S | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT |
| DS1821 | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 1Cel, ROUND, SURFACE MOUNT |
| DS1821T | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822-PAR+T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822-PAR/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1821S/T&R | 制造商:Maxim Integrated Products 功能描述:PROGRAM THERMOSTAT 208ML 8-SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT PROG 8-SOIC |
| DS1821S/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1821S/TR | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Programmable Digital Thermostat and Thermometer |
| DS1821S+ | 功能描述:板上安裝溫度傳感器 Programmable Digital Thermostat/Thrmmtr RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1821S+R | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Programmable Digital Thermostat and Thermometer |
發布緊急采購，3分鐘左右您將得到回復。