- 您現在的位置：買賣IC網 > PDF目錄376961 > DS1820 1-Wire Digital Thermometer PDF資料下載
參數資料
| 型號： | DS1820 |
| 英文描述： | 1-Wire Digital Thermometer |
| 文件頁數： | 16/27頁 |
| 文件大?。?/td> | 151K |
| 代理商： | DS1820 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
DS1820
030598 16/27
INITIALIZATION PROCEDURE “RESET AND PRESENCE PULSES”
Figure 11
Master T
X
“reset pulse”
480
μ
s minimum
960
μ
s maximum
Master R
480
μ
s minimum
V
CC
GND
DS1820
waits
15 - 60
μ
s
DS1820 T
“presence pulse”
60 - 240
μ
s
LINE TYPE LEGEND:
Bus master active low
Both bus master and
DS1820 active low
DS1820 active low
Resistor pull–up
1–WIRE
BUS
DS1820 COMMAND SET
Table 2
INSTRUCTION
DESCRIPTION
PROTOCOL
1–WIRE BUS
AFTER ISSUING
PROTOCOL
NOTES
TEMPERATURE CONVERSION COMMANDS
Convert T
Initiates temperature conversion.
44h
<read temperature
busy status>
1
MEMORY COMMANDS
Read Scratchpad
Reads bytes from scratchpad and
reads CRC byte.
BEh
<read data up to 9
bytes>
Write Scratchpad
Writes bytes into scratchpad at
addresses 2 and 3 (TH and TL
temperature triggers).
4Eh
<write data into 2
bytes at addr. 2 and
addr. 3>
Copy Scratchpad
Copies scratchpad into nonvolatile
memory (addresses 2 and 3 only).
48h
<read copy status>
2
Recall E
2
Recalls values stored in nonvolatile
memory into scratchpad (tempera-
ture triggers).
B8h
<read temperature
busy status>
Read Power Supply
Signals the mode of DS1820
power supply to the master.
B4h
<read supply status>
NOTES:
1. Temperature conversion takes up to 500 ms. After receiving the Convert T protocol, if the part does not
receive power from the V
DD
pin, the I/O line for the DS1820 must be held high for at least 500 ms to provide
power during the conversion process. As such, no other activity may take place on the 1–Wire bus for at least
this period after a Convert T command has been issued.
2. After receiving the Copy Scratchpad protocol, if the part does not receive power from the V
DD
pin, the I/O line
for the DS1820 must be held high for at least 10 ms to provide power during the copy process. As such, no
other activity may take place on the 1–Wire bus for at least this period after a Copy Scratchpad command has
been issued.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1821 | Programmable Digital Thermostat |
| DS1830 | Reset Sequence Pushbutton |
| DS1830A | Reset Sequence Pushbutton |
| DS1830AS | Reset Sequence Pushbutton |
| DS1830AU | Reset Sequence Pushbutton |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1820K | 制造商:Maxim Integrated Products 功能描述:THERMOMETER DEMO KIT |
| DS1820S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DS1820.DS1820S Digital Thermometer Replacements |
| DS1821 | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1821_07 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Programmable Digital Thermostat and Thermometer |
| DS1821+ | 功能描述:板上安裝溫度傳感器 Programmable Digital Thermostat/Thrmmtr RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。