- 您現在的位置：買賣IC網 > PDF目錄376960 > DS1809Z-100 Dallastat, 64-position linear taper PDF資料下載
參數資料
| 型號： | DS1809Z-100 |
| 英文描述： | Dallastat, 64-position linear taper |
| 中文描述： | Dallastat，64位線性錐 |
| 文件頁數： | 2/8頁 |
| 文件大小： | 87K |
| 代理商： | DS1809Z-100 |
DS1809
101999
2 of 8
The DS1809 is available in standard 10 k
, 50 k
, and 100 k
resistor versions. The DS1809 is
provided as an industrial temperature grade part only. Available packaging for the DS1809 include an 8-
lead (300-mil) DIP an 8-lead (150-mil) SOIC, and an 8-lead (118-mil)
μ
SOP.
BLOCK DIAGRAM
Figure 1
OPERATION
The DS1809 Dallastat is a digitally controlled, nonvolatile potentiometer. A block diagram of the
DS1809 is shown in Figure 1. The DS1809 is a linear potentiometer providing 64-uniform wiper
positions over the entire resistor range including the end-terminals. All three potentiometer terminals of
the device are accessible. These terminals include R
H
, R
L
, and R
W
. R
H
and R
L
are the end-terminals of the
potentiometer. These terminals will have a constant resistance between them as defined by the
potentiometer value chosen: 10 k
, 50 k
, or the 100 k
version. Functionally, R
H
and R
L
are
interchangeable. The wiper terminal, R
W
, is the multiplexed terminal and can be set to one of the 64 total
positions that exist on the resistor ladder including the R
H
and R
L
terminals.
Control of the wiper (R
W
) position setting is accomplished via the two inputs UC and DC. The UC and
DC control inputs, when active, determine the direction on the resistor array that the wiper position will
move. The UC (up control) control input is used to move the wiper position towards the R
H
terminal. The
DC (down control) control input is used to move wiper position towards the R
L
terminal.
The control inputs UC and DC are active low inputs which interpret input pulse widths as the means of
controlling wiper movement. Internally, these inputs are pulled up to V
CC
via a 100 k
resistance. A
transition from a high-to-low on these inputs is considered the beginning of pulse input activity.
A single pulse on the UC or DC input is defined as being greater than 1 millisecond but lasting no longer
that second. This type pulse input will cause the wiper position of the Dallastat to move one position.
Multiple pulse inputs (repetitive pulse inputs) can be used to step through each wiper position of the
device. The requirement for a repetitive pulse train on the UC or DC inputs is that pulses must be
separated by a minimum high time of 1 millisecond. If this is not the case the Dallastat will ignore that
pulse input.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1809-050 | Dallastat, 64-position linear taper |
| DS1809-100 | Dallastat, 64-position linear taper |
| DS1809 | Dallastat, 64-position linear taper |
| DS1810 | Desoldering, Tool, Depth 0.060 Inches, Width 0.060 Inches |
| DS1810-10 | 5V EconoReset with Push-Pull Output |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1809Z-100+ | 功能描述:數字電位計 IC Dallastat RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1809Z50 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| DS1809Z-W10+ | 功能描述:數字電位計 IC Dallastat RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS180RT | 制造商:C&K Components 功能描述:DS180RT / Alt#: HADS0009 / Series: COMAX |
| DS1810 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:5V EconoReset with Push-Pull Output |
發布緊急采購，3分鐘左右您將得到回復。