- 您現(xiàn)在的位置：買賣IC網 > PDF目錄9058 > DS1808Z-050 (Maxim Integrated Products)IC POT DUAL LOG HV 50K 16-SOIC PDF資料下載
參數資料
| 型號： | DS1808Z-050 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/17頁 |
| 文件大小： | 0K |
| 描述： | IC POT DUAL LOG HV 50K 16-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 接片： | 32 |
| 電阻（歐姆）： | 45k |
| 電路數： | 2 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 4.5 V ~ 5.5 V，±4.5 V ~ 13.2 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 管件 |
DS1808
14 of 17
NOTES:
1. All voltages are referenced to ground.
2. I/O pins of fast mode devices must not obstruct the SDA and SCL lines if VCC is switched off.
3. The value of VDD should never exceed VCC, including during power-ups. VCC must be applied before
either VDD or VB. VDD and VB can then follow in any order.
4. ISTBY specified for VDD equal to 5.0V. Control port logic pins are driven to the appropriate logic
levels. Appropriate logic levels specify that logic inputs are within a 0.5V of ground or VDD for the
corresponding inactive state.
5. A fast mode device can be used in a standard mode system, but the requirement tSU:DAT > 250ns
must then be met. This will automatically be the case if the device does not stretch the LOW period of
the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the
next data bit to the SDA line tRMAX + tSU:DAT = 1000 + 250 = 1250ns before the SCL line is
released.
6. After this period, the first clock pulse is generated.
7. The maximum tHD:DAT has only to be met if the device does not stretch the LOW period (tLOW) of
the SCL signal.
8. CB – Total capacitance of one bus line in picofarads, timing referenced to (0.9)(VDD) and (0.1)(VDD).
9. Absolute linearity is used to measure expected wiper voltage as determined by wiper position.
10. Relative linearity is used to determine the change of wiper voltage between two adjacent wiper
positions.
11. When used as a rheostat or variable resistor the resistance temperature coefficient is: 750ppm/°C.
When used as a voltage divider or potentiometer, the output voltage temperature coefficient
approaches 30 ppm/°C.
12. ICC specified with SDA pin open.
13. Maximum ICC is dependent on clock rates.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1801 | IC POT DUAL AUDIO TAPER 14-PDIP |
| DS1807 | IC POT ADDRESS 2X AUDIO 14-DIP |
| MS3456L24-12SW | CONN PLUG 5POS STRAIGHT W/SCKT |
| MS3456L24-12S | CONN PLUG 5POS STRAIGHT W/SCKT |
| M83723/77W22558 | CONN PLUG 55POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1808Z-050/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL LOG HI VOLTAGE POT T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT DUAL LOG HV 50K 16-SOIC |
| DS1808Z-050/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1808Z-050+ | 功能描述:數字電位計 IC Dual Log RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1808Z-050+T&R | 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 32POS 45KOHM DUAL 16SOIC N - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT DUAL LOG HV 50K 16-SOIC |
| DS1808Z-050+T&R | 功能描述:數字電位計 IC Dual Log RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。