- 您現在的位置：買賣IC網 > PDF目錄9396 > DS1808Z-050+ (Maxim Integrated Products)IC POT DUAL LOG HV 50K 16-SOIC PDF資料下載
參數資料
| 型號： | DS1808Z-050+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 15/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DUAL LOG HV 50K 16-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 接片： | 32 |
| 電阻（歐姆）： | 45k |
| 電路數： | 2 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 4.5 V ~ 5.5 V，±4.5 V ~ 13.2 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1430 (CN2011-ZH PDF) |
DS1808
7 of 17
READING THE DS1808
As shown in Figure 4, the DS1808 provides one read command operation. This operation allows the user
to read both potentiometers. To initiate a read operation, the R/W bit of the command/control byte is set
to 1. Communication to read the DS1808 begins with a start condition, which is issued by the master
device. The command/control byte from the master device will follow the start condition. Once the
command/control byte has been received by the DS1808, the part will respond with an acknowledge.
When the master has received the acknowledge from the DS1808, the master can then begin to receive
wiper data. The value of the wiper of potentiometer-0 will be the first returned from the DS1808. It will
then be followed by the value of potentiometer-1. Once the 8-bits of potentiometer-0 have been
transmitted, the master will need to issue an acknowledge, unless it is the only byte to be read, in which
case the master issues a ‘not acknowledge.’ If desired, the master may stop the communication transfer at
this point by issuing the stop condition. However, if the value of the remaining potentiometer is needed,
transfer can continue by clocking the 8 bits of the potentiometer-1 value, followed by a not acknowledge.
WRITING TO THE DS1808
A data flow diagram of the DS1808 is shown in Figure 5. The DS1808 has one write command that is
used to change the position of the wiper(s). All write operations begin with a START from the master,
followed by a command/control byte. The R/W bit should be written to 0b, which initiates a write
command. Once the command/control byte has been issued and the master receives the
ACKNOWLEDGE from the DS1808, potentiometer wiper data is transmitted to the DS1808 by the
master device.
Figure 2
相關PDF資料 |
PDF描述 |
|---|---|
| MS27472T24A61SA | CONN RCPT 61POS WALL MT W/SCKT |
| DS1673S-5+ | IC CTRLR SYSTEM PORT 5V 20-SOIC |
| DS1844S-050+ | IC POT DIG QUAD 50K 20-SOIC |
| DS1803Z-100+ | IC POT DUAL ADDRESS 100K 16-SOIC |
| DS1803Z-010+ | IC POT DUAL ADDRESS 10K 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1808Z-050/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL LOG HI VOLTAGE POT T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT DUAL LOG HV 50K 16-SOIC |
| DS1808Z-050/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1808Z-050+ | 功能描述:數字電位計 IC Dual Log RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1808Z-050+T&R | 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 32POS 45KOHM DUAL 16SOIC N - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT DUAL LOG HV 50K 16-SOIC |
| DS1808Z-050+T&R | 功能描述:數字電位計 IC Dual Log RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。