- 您現在的位置：買賣IC網 > PDF目錄376960 > DS1807E Addressable Dual Audio Taper Potentiometer PDF資料下載
參數資料
| 型號： | DS1807E |
| 元件分類： | 數字電位計 |
| 英文描述： | Addressable Dual Audio Taper Potentiometer |
| 中文描述： | 錐形雙音頻尋址電位 |
| 文件頁數： | 12/13頁 |
| 文件大?。?/td> | 463K |
| 代理商： | DS1807E |
DS1807
12 of 13
110499
NOTES:
1.
All voltages are referenced to ground.
2.
I/O pins of fast mode devices must not obstruct the SDA and SCL lines if V
DD
is switched off.
3.
I
CC
specified with zero-crossing detection active and operating device serial port in fast mode.
4.
I
STBY
specified with for V
CC
equal 3.0V and 5.0V and SDA and SCL are driven to the appropriate
logic levels. I
STBY
is specified as the current consumption of the device when SDA and SCL are in the
inactive (high) states.
5.
After this period, the first clock pulse is generated.
6.
A device must internally provide a hold time of at least 300 ns for the SDA signal (referred to the
V
IHMIN
of the SCL signal) in order to bridge the undefined region of the falling edge of SCL.
7.
The maximum t
HD:DAT
has only to be met if the device does not stretch the LOW period (t
LOW
) of the
SCL signal.
8.
A fast mode device can be used in a standard mode system, but the requirement t
SU:DAT
> 250 ns must
then be met. This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next
data bit to the SDA line t
RMAX
+ t
SU:DAT
= 1000+250=1250 ns before the SCL line is released.
9.
C
B
- total capacitance of one bus line in picofarads, timing referenced to (0.9(V
CC
) and (0.1)(V
CC
)).
10.
Absolute tolerance is used to determine measured wiper voltage versus expected wiper voltage as
determined by wiper position.
11.
Tap-to-tap tolerance is used to determine the change in voltage between successive tap positions. The
DS1807 is specified for a
±
0.25 dB tap-to-tap tolerance.
12.
Typical values are for t
A
= 25
°
C and nominal supply voltage.
13.
Address inputs, A0, A1, and A2, should be tied to either V
CC
or GND depending on the desired
address selections.
14.
These parameters are characterized and not 100% tested.
15.
Interchannel matching is used to determine the relative difference in dB between the same position on
each potentiometer. The DS1807 is specified for
±
0.5 dB Interchannel matching
16.
See Figure 9.
17.
Valid at 25
°
C only.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1807S | Addressable Dual Audio Taper Potentiometer |
| DS1808 | Dual Log Digital Potentiometer |
| DS1808 | Process: 1P, 1M, 5.0um, 30V NF & PF, UVNd, UVPd ,N+ESD,TEOS Spacer, Passivation w/Nov TEOS Oxide-Nitride |
| DS1809-010 | Dallastat, 64-position linear taper |
| DS1809U-010 | Dallastat, 64-position linear taper |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1807E/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1807E+ | 功能描述:數字電位計 IC Addressable Dual Audio Taper RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1807E+ | 制造商:Maxim Integrated Products 功能描述:IC DIGITAL POT 45KOHM 64 DUA |
| DS1807E+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 65POS 45KOHM DUAL 14TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT ADDRESS 2X AUDIO 14-TSSOP 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer ICs Addressable Dual Audio Taper |
| DS1807E+T&R | 功能描述:數字電位計 IC Addressable Dual Audio Taper RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。