- 您現在的位置：買賣IC網 > PDF目錄9182 > DS1804U-050+T&R (Maxim Integrated Products)IC POT TRIMMER NV 50K 8-USOP PDF資料下載
參數資料
| 型號： | DS1804U-050+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT TRIMMER NV 50K 8-USOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 3,000 |
| 接片： | 100 |
| 電阻（歐姆）： | 50k |
| 電路數： | 1 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 3 線（芯片選擇，遞增，增/減） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 帶卷 (TR) |
DS1804
6 of 10
NOTES:
1) All voltages are referenced to ground.
2) Valid for VCC = 5V only.
3) Resistor input voltages cannot go below ground or exceed VCC by the amounts as shown in the table.
4) Maximum current specifications are based on the clock rate of INC input. This specification
represents the current required when changing the wiper position.
5) Standby current levels apply when all inputs are driven to appropriate supply levels. CS , INC , U/ D =
VCC.
6) Wiper load time is specified as the time required for the DS1804 to load the wiper position with the
contents of nonvolatile memory once VCC has reached a stable operating voltage equal to or greater
than 2.7V.
7) The DS1804 is available in three resistor values. These include the DS1804-010, 10k
; the DS1804-
050, 50k
; and the DS1804-100, 100k.
8) Valid at TA = +25°C only.
9) Absolute linearity is used to compare measured wiper voltage versus expected wiper voltage as
determined by wiper position. The DS1804 is specified to provide an absolute linearity of ±0.60 LSB.
10) Relative linearity is used to determined the change in voltage between successive tap positions. The
DS1804 is specified to provide a relative linearity specification of ±0.25 LSB.
11) -3dB cutoff frequency characteristics for the DS1804 depend on potentiometer total resistance.
DS1804-010, 1MHz; DS1804-050, 200kHz; and DS1804-100, 100kHz.
12) Capacitance values apply at TA = +25°C.
13) See Figure 2.
14) Power-up time is specified as the time required before the three-terminal control becomes active after
a stable power supply level has been reached.
15) At VCC = 2.7V, VIL = 0.8V.
16) The INC low to CS inactive is specified to be 50ns minimum. This is the transition condition which
allows the DS1804 three-terminal port to become inactive without writing the EEPROM memory of
the part.
17) Wiper Storage Time, tWST, is the time require for the DS1804 to write EEPROM memory for storage
of a new wiper position. The maximum time required to accomplish this task is specified at 10ms.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3456W18-13PX | CONN PLUG 4POS STRAIGHT W/PINS |
| DS1804Z-050+T&R | IC POT TRIMMER NV 50K 8-SOIC |
| 7SB3257DTT1G | 1 BIT MUX/DEMUX BUS SWTCH TSOP6 |
| 7SB3257DFT2G | 1 BIT MUX/DEMUX BUS SWTCH SC-88A |
| MS3456W18-13PW | CONN PLUG 4POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1804U-100 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1804U-100/T&R | 制造商:Maxim Integrated Products 功能描述:NV TRIMMER POT 100K 8P USOP T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT TRIMMER NV 100K 8-USOP 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer ICs NV Trimmer |
| DS1804U-100/T&R | 功能描述:數字電位計 IC NV Trimmer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1804U-100+ | 功能描述:數字電位計 IC NV Trimmer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1804U-100+T&R | 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 100POS 100KOHM SGL 8PIN UMAX - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT TRIMMER NV 100K 8-USOP 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer ICs NV Trimmer |
發(fā)布緊急采購，3分鐘左右您將得到回復。