- 您現在的位置：買賣IC網 > PDF目錄9315 > DS17485S-5/T&R (Maxim Integrated Products)IC RTC 5V 4K NV RAM 24-SOIC PDF資料下載
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁
DS17285/DS17287/DS17485/DS17487/DS17885/DS17887
Real-Time Clocks
8
_____________________________________________________________________
Pin Description (continued)
PIN
24
28
NAME
FUNCTION
13
23
CS
Active-Low Chip-Select Input. This pin must be asserted low during a bus cycle for the
device to be accessed.
CS must be kept in the active state during RD and WR. Bus cycles
that take place without asserting
CS latch addresses, but no access occurs.
14
24
ALE
Address Latch Enable Input, Active High. This input pin is used to demultiplex the
address/data bus. The falling edge of ALE causes the address to be latched within the
device.
15
25
WR
Active-Low Write Input. This pin defines the period during which data is written to the
addressed register.
17
27
RD
Active-Low Read Input. This pin identifies the period when the device drives the bus with
read data. It is an enable signal for the output buffers of the device.
18
28
KS
Active-Low Kickstart Input. When VCC is removed from the device, the system can be
powered on in response to an active-low transition on the
KS pin, as might be generated
from a key closure. VBAUX must be present and auxiliary-battery-enable bit (ABE) must be
set to 1 if the kickstart function is used, and the
KS pin must be pulled up to the VBAUX
supply. While VCC is applied, the
KS pin can be used as an interrupt input. If not used, KS
must be grounded and ABE set to 0.
19
1
IRQ
Active-Low Interrupt Request. This pin is an active-low output that can be used as an
interrupt input to a processor. The
IRQ output remains low as long as the status bit causing
the interrupt is present and the corresponding interrupt-enable bit is set. To clear the
IRQ
pin, the application software must clear all enabled flag bits contributing to the pin’s active
state. When no interrupt conditions are present, the
IRQ level is in the high-impedance
state. Multiple interrupting devices can be connected to an
IRQ bus, provided that they are
all open drain. The
IRQ pin requires an external pullup resistor to VCC.
20
2
VBAT
Connection for Primary Battery. This supply input is used to power the normal clock
functions when VCC is absent. Diodes placed in series between VBAT and the battery can
prevent proper operation. If VBAT is not required, the pin must be grounded. UL recognized
to ensure against reverse charging current when used with a lithium battery (www.maxim-
ic.com/qa/info/ul). This pin is missing (N.C.) on the EDIP package.
相關PDF資料 |
PDF描述 |
|---|---|
| MCP42010T-E/ST | IC POT DGTL 10K 2CH SPI 14TSSOP |
| MCP42010T-E/SL | IC POT DGTL 10K 2CH SPI 14SOIC |
| DS1501WSN/T&R | IC RTC WDOG Y2KC 3.3V IND 28SOIC |
| MCP42010-E/ST | IC POT DGTL 10K 2CH SPI 14TSSOP |
| DS1689SN/T&R | IC RTC SER NV RAM CTRL IN 28SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS17485SN-3 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3V/5V Real-Time Clock |
| DS17485SN5 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Real-Time Clocks |
| DS17485SN-5 | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17485SN-5/T&R | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17485SN-5+ | 功能描述:實時時鐘 3V/5V RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。