參數資料
型號： DS17485-DS17487
英文描述： 3V/5V Real-Time Clock
中文描述： 3V/5V實時時鐘
文件頁數： 21/38頁
文件大?。?/td> 427K
代理商： DS17485-DS17487
DS17485/DS17487
21 of 38
EXTENDED CONTROL REGISTERS
Two extended control registers are provided to supply controls and status information for the extended
features offered by the DS17485/DS17487. These are designated as extended control registers 4A and 4B
and are located in register bank 1, locations 04AH and 04BH, respectively. The functions of the bits
within these registers are described as follows.
EXTENDED CONTROL REGISTER 4A
MSB
BIT 7
BIT 6
BIT 5
BIT 4
VRT2
INCR
BME
*
VRT2 – Valid RAM and Time 2.
A read-only status bit. When VRT2 = 0, the RTC and RAM data are
questionable and indicates that the lithium energy source connected to the V
BAUX
input has been
exhausted and should be replaced. This bit indicates the status of the V
BAUX
input.
INCR – Increment in Progress Status.
This bit is set to a 1 when an increment to the time/date registers
is in progress and the alarm checks are being made. INCR is set to a 1 at 122μs before the update cycle
starts and is cleared to 0 at the end of each update cycle.
BME – Burst Mode Enable.
The burst mode enable bit allows the extended user RAM address registers
to automatically increment for consecutive reads and writes. When BME is set to a logic 1, the automatic
incrementing is enabled and when BME is set to a logic 0, the automatic incrementing is disabled.
PAB – Power-Active Bar-Control.
When this bit is 0, the
PWR
pin is in the active low state. When this
bit is 1, the
PWR
pin is in the high-impedance state. This bit can be written to a logic 1 or 0 by the user. If
either WF and WIE = 1 or KF and KSE = 1, the PAB bit is cleared to 0.
RF – Ram Clear Flag.
This bit is set to a logic 1 when a high-to-low transition occurs on the
RCLR
input if RCE = 1. The RF bit is cleared by writing it to a logic 0. This bit can also be written to a logic 1
to force an interrupt condition.
WF – Wake-Up Alarm Flag.
This bit is set to 1 when a wake-up alarm condition occurs or when the
user writes it to a 1. WF is cleared by writing it to a 0.
KF – Kickstart Flag
. This bit is set to a 1 when a kickstart condition occurs or when the user writes it to
a 1. This bit is cleared by writing it to a logic 0.
*Reserved bits. These bits are reserved for future use by Dallas Semiconductor. They can be read and
written, but have no affect on operation.
LSB
BIT 0
KF
BIT 3
PAB
BIT 2
RF
BIT 1
WF
相關PDF資料
PDF描述
DS17485 3V/5V Real-Time Clock
DS17485E-3 3V/5V Real-Time Clock
DS17485E-5 3V/5V Real-Time Clock
DS17485EN-3 3V/5V Real-Time Clock
DS17485EN-5 3V/5V Real-Time Clock
相關代理商/技術參數
參數描述
DS17485E3 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Real-Time Clocks
DS17485E-3 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS17485E-3+ 功能描述:實時時鐘 3V/5V RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS17485E5 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Real-Time Clocks
DS17485E-5 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*