參數資料
型號： DS1742-70
英文描述： Y2KC Nonvolatile Timekeeping RAM
中文描述： Y2KC非易失內存時鐘
文件頁數： 4/12頁
文件大小： 163K
代理商： DS1742-70
DS1742
4 of 12
address inputs are changed while
CE
, and
OE
remain valid, output data will remain valid for output data
hold time (t
OH
) but will then go indeterminate until the next address access.
WRITING DATA TO RAM OR CLOCK
The DS1742 is in the write mode whenever
WE
, and
CE
are in their active state. The start of a write is
referenced to the latter occurring transition of
WE
, on
CE
. The addresses must be held valid throughout
the cycle.
CE
, or
WE
must return inactive for a minimum of t
WR
prior to the initiation of another read or
write cycle. Data in must be valid t
DS
prior to the end of write and remain valid for t
DH
afterward. In a
typical application, the
OE
signal will be high during a write cycle. However,
OE
can be active provided
that care is taken with the data bus to avoid bus contention. If
OE
is low prior to
WE
transitioning low
the data bus can become active with read data defined by the address inputs. A low transition on
WE
will
then disable the outputs t
WEZ
after
WE
goes active.
DATA RETENTION MODE
The 5-volt device is fully accessible and data can be written or read only when V
CC
is greater than V
PF
.
However, when V
CC
is below the power fail point, V
PF
,
(point at which write protection occurs) the
internal clock registers and SRAM are blocked from any access. At this time the power fail reset output
signal (
RST
) is driven active and will remain active until V
CC
returns to nominal levels. When V
CC
falls
below the battery switch point V
SO
(battery supply level), device power is switched from the V
CC
pin to
the backup battery. RTC operation and SRAM data are maintained from the battery until V
CC
is returned
to nominal levels. The 3.3 volt device is fully accessible and data can be written or read only when V
CC
is
greater than V
PF
.
When V
CC
falls below the power fail point, V
PF
,
access to the device is inhibited. At this
time the power fail reset output signal (
RST
) is driven active and will remain active until V
CC
returns to
nominal levels. If V
PF
is less than Vso
,
the device power is switched from V
CC
to the backup supply (V
BAT
)
when V
CC
drops below V
PF
.
If V
PF
is greater than Vso
,
the device power is switched from V
CC
to the
backup supply (V
BAT
)
when V
CC
drops below Vso
.
RTC operation and SRAM data are maintained from
the battery until V
CC
is returned to nominal levels. The
RST
signal is an open drain output and requires a
pull up. Except for the
RST
, all control, data, and address signals must be powered down when V
CC
is
powered down.
BATTERY LONGEVITY
The DS1742 has a lithium power source that is designed to provide energy for clock activity, and clock
and RAM data retention when the V
CC
supply is not present. The capability of this internal power supply
is sufficient to power the DS1742 continuously for the life of the equipment in which it is installed. For
specification purposes, the life expectancy is 10 years at 25
°
C with the internal clock oscillator running in
the absence of V
CC
power. Each DS1742 is shipped from Dallas Semiconductor with its lithium energy
source disconnected, guaranteeing full energy capacity. When V
CC
is first applied at a level greater than
V
PF
, the lithium energy source is enabled for battery backup operation. Actual life expectancy of the
DS1742 will be much longer than 10 years since no lithium battery energy is consumed when V
CC
is
present.
BATTERY MONITOR
The DS1742 constantly monitors the battery voltage of the internal battery. The Battery Flag bit (bit 7) of
the day register is used to indicate the voltage level range of the battery. This bit is not writable and
should always be a 1 when read. If a 0 is ever present, an exhausted lithium energy source is indicated
and both the contents of the RTC and RAM are questionable.
相關PDF資料
PDF描述
DS1742W-120 Y2KC Nonvolatile Timekeeping RAM
DS1742W-150 Y2KC Nonvolatile Timekeeping RAM
DS1742 Y2KC Nonvolatile Timekeeping RAM
DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs
DS1746-70IND Y2K-Compliant, Nonvolatile Timekeeping RAMs
相關代理商/技術參數
參數描述
DS1742-70+ 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS1742-85 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Y2KC Nonvolatile Timekeeping RAMwww.
DS1742-85+ 功能描述:實時時鐘 Timekeeping NV RAM RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS1742W-120 功能描述:實時時鐘 Timekeeping NV RAM RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS1742W-120+ 功能描述:實時時鐘 Timekeeping NV RAM RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*