- 您現在的位置：買賣IC網 > PDF目錄97863 > DS1726U/T&R (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | DS1726U/T&R |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | MICRO, SOP-8 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 141K |
| 代理商： | DS1726U/T&R |
DS1626/DS1726
8 of 12
CPU BIT AND STAND-ALONE THERMOSTAT OPERATION
In stand-alone thermostat mode, DS1626/DS1726 thermostat functionality can be used without requiring
a microcontroller to start/stop temperature conversions. The CPU bit in the configuration register
determines if stand-alone mode is enabled.
When CPU = 1 stand-alone mode is disabled, and the only way to start/stop temperature conversions is
by using a microcontroller to transmit Start Convert T and Stop Convert T commands, respectively.
Stand-alone mode is enabled when CPU = 0. In this mode, when
RST = 0 the CLK/CNV pin operates as
a control signal to start and stop temperature measurements. Driving CLK/
CNV low initiates continuous
temperature conversions that will continue until CLK/
CNV is brought high again. If the CLK/CNV pin is
driven low and then returned to a high state in less than 10ms, only one temperature conversion will be
performed after which the DS1626/DS1726 will return to a low-power idle state (i.e., one-shot operation).
Note that when stand-alone mode is enabled, the 1SHOT bit in the configuration register is ignored, and
only the CLK/
CNV signal determines whether continuous or one-shot conversions take place.
Since TH, TL, and the CPU bit are stored in EEPROM, the DS1626/DS1726 can be preprogrammed for
stand-alone operation. If desired, the CLK/
CNV and RST pin can be connected to GND so the
DS1626/DS1726 will automatically begin taking temperature measurements at power-up
Normal bus communication with the DS1626/DS1726 can still take place in stand-alone mode when
RST = 1. When communication is initiated, stand-alone conversions are automatically halted. If during
the bus communication continuous temperature conversions are started using the Start Convert T
command, they can only be stopped by issuing a Stop Convert T command.
Figure 5. THERMOSTAT OUTPUT OPERATION
TL
TH
TEMP
LOGIC 0
LOGIC 1
TCOM
TEMP
LOGIC 0
LOGIC 1
THIGH
TEMP
LOGIC 0
LOGIC 1
TLOW
相關PDF資料 |
PDF描述 |
|---|---|
| DS1626U/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| DS1626U | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| DS1726U+ | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| DS17285E-3 | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| DS17285E-5 | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS17285 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3V/5V Real-Time Clock |
| DS17285_1 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Real-Time Clocks |
| DS17285-3 | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17285-3+ | 功能描述:實時時鐘 3V/5V RTC K Multiplexed Kick-S RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17285-5 | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。