- 您現在的位置：買賣IC網 > PDF目錄376958 > DS1722S IC-SM-DIGITAL THERMOMETER PDF資料下載
參數資料
| 型號： | DS1722S |
| 元件分類： | 溫度傳感器 |
| 英文描述： | IC-SM-DIGITAL THERMOMETER |
| 中文描述： | 集成電路釤數字溫度計 |
| 文件頁數： | 6/13頁 |
| 文件大小： | 984K |
| 代理商： | DS1722S |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
DS1722
6 of 13
The SDI and SDO pins are the serial data input and output pins for the DS1722, respectively. The CE
input is used to initiate and terminate a data transfer. The SCLK pin is used to synchronize data
movement between the master (microcontroller) and the slave (DS1722) devices.
The shift clock (SCLK), which is generated by the microcontroller, is active only when CE is high and
during address and data transfer to any device on the SPI bus. The inactive clock polarity is
programmable in some microcontrollers. The DS1722 offers an important feature in that the level of the
inactive clock is determined by sampling SCLK when CE becomes active. Therefore, either SCLK
polarity can be accommodated. Input data (SDI) is latched on the internal strobe edge and output data
(SDO) is shifted out on the shift edge (See Table 5 and Figure 3). There is one clock for each bit
transferred. Address and data bits are transferred in groups of eight, MSB first.
FUNCTION TABLE
Table 5
MODE
Disable Reset
Write
CE
L
H
SCLK
SDI
SDO
Input Disabled
CPOL=1*
Input Disabled
Data Bit Latch
High Z
High Z
CPOL=0
CPOL=1
Read
H
CPOL=0
X
Next data bit
shift**
*CPOL is the “Clock Polarity” bit that is set in the control register of the microcontroller.
** SDO remains at High Z until eight bits of data are ready to be shifted out during a read.
NOTE:
CPHA bit polarity must be set to “1”.
SERIAL CLOCK AS A FUNCTION OF MICROCONTROLLER CLOCK
POLARITY (CPOL)
Figure 3
CPOL=1
CPOL=0
NOTE:
CPOL is a bit that is set in the microcontroller’s Control Register.
CE
SCLK
CE
SCLK
INTERNAL
STROBE
SHIFT
INTERNAL
STROBE
SHIFT
相關PDF資料 |
PDF描述 |
|---|---|
| DS1722 | Digital Thermometer with SPI/3-Wire Interface |
| DS1730Y-150 | NVRAM (Battery Based) |
| DS1730Y-150-IND | NVRAM (Battery Based) |
| DS1730Y-200 | NVRAM (Battery Based) |
| DS1730Y-200-IND | NVRAM (Battery Based) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1722S/T&R | 制造商:Maxim Integrated Products 功能描述:SPI 3-WIRE THERMOMETER SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER DIG 3-WIRE 8-SOIC |
| DS1722S/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1722S+ | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1722S+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 3-WIRE/SPI 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER DIG 3-WIRE 8-SOIC |
| DS1722S+T&R | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。