- 您現在的位置：買賣IC網 > PDF目錄97863 > DS1722S+ (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | DS1722S+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | 0.150 INCH, LEAD FREE, SOIC-8 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 194K |
| 代理商： | DS1722S+ |
MAX6701–08/MAX6701A–03A/05A–07A
Low-Voltage, SOT23 P Supervisors with Power-
Fail In/Out, Manual Reset, and Watchdog Timer
8
_______________________________________________________________________________________
Standard- vs. A-Version Comparison
The MAX6701/MAX6702/MAX6703/MAX6705/MAX6706/
MAX6707s’ WDO latches low when one of the following
events occurs:
The watchdog timer times out (1.6s, typ).
VCC, RST_IN1, or RST_IN2 is below its reset threshold.
MR is pulled low.
WDO only deasserts with a valid WDI transition.
TheMAX6701(A)/MAX6702(A)/MAX6703(A)/MAX6705(A)/
MAX6706(A)/MAX6707(A)s’ WDO asserts when either
VCC, RST_IN1, or RST_IN2 is below its reset threshold.
WDO deasserts without a timeout delay when the
undervoltage situation has expired. WDO is latched low
when the watchdog timer elapses without seeing a WDI
transition. WDO deasserts with a valid WDI transition
OR by pulling MR low.
See Figures 4 and 5 for standard-version timing. See
Figures 6 and 7 for A-version timing.
Watchdog Timer
The MAX6701–MAX6707 watchdog circuit monitors the
P’s activity. If the P does not toggle the WDI within 1.6s,
WDO goes low. When RESET is asserted, the watchdog
timer stays cleared and does not count. As soon as reset
is released, the timer starts counting. WDO deasserts
after a valid transition is detected at WDI. Pulses as short
as 50ns can be detected.
Typically, WDO is connected to the NMI input of a P.
When VCC, RST_IN1, or RST_IN2 drop below the reset
threshold, WDO goes low whether or not the watchdog
timer has timed out. Normally this would trigger an NMI,
but RESET goes low simultaneously, and thus overrides
the NMI.
The MAX6704 watchdog circuit does not have an inde-
pendent watchdog output (WDO). If the P does not
toggle the watchdog input within 1.6s, the MAX6704
asserts a reset output pulse for the reset timeout period.
Manual Reset
The manual reset input (MR) allows reset to be trig-
gered by a pushbutton switch. The switch is effectively
debounced by the reset pulse width. MR is CMOS logic
compatible, so it can be driven by an external logic
line. MR can be used to force a watchdog timeout to
generate a reset pulse in the MAX6701(A)/MAX6702(A)/
MAX6703(A)/MAX6705(A)/MAX6706(A)/MAX6707(A) by
connecting WDO to MR.
Power-Fail Comparator
The uncommitted power-fail comparator can be used
for various purposes because its noninverting input and
output are externally available. The inverting input is
internally connected to a 0.62V reference. To build an
early warning circuit for power failure, connect the PFI
pin to a voltage-divider (see the Typical Operating
Circuit). Choose the voltage-divider ratio so that the
voltage at PFI falls below 0.62V just before the regulator
drops out. Use PFO to interrupt the P so it can prepare
for an orderly power-down. The low-input current at this
pin allows for large resistor values in the divider.
tWD
+5V
0V
WDI
+5V
0V
WDO
+5V
0V
RESET
+5V
0V
(RESET)
tRP
RESET EXTERNALLY
TRIGGERED BY MR
+5V
0V
MR
( ) ARE FOR MAX6702/MAX6706 ONLY.
tWDI
tRP
+5V
0V
RESET
WDO
+5V
0V
MR
tMR
+5V
0V
VCC
VTH
tMD
Figure 5. MAX6701/MAX6702/MAX6703/MAX6705/MAX6706/
MAX6707 Watchdog
Figure 6. MAX6701(A)/MAX6702(A)/MAX6703(A)/MAX6705(A)/
MAX6706(A)/MAX6707(A) RESET, MR, and WDO Timing with
WDI Three-Stated
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6708 | 低電壓、SOT23封裝、微處理器監控電路，帶有電源失效檢測輸入/輸出、手動復位及看門狗定時器 |
| DS1726U/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| DS1626U/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| DS1626U | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| DS1726U+ | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1722S/T&R | 制造商:Maxim Integrated Products 功能描述:SPI 3-WIRE THERMOMETER SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER DIG 3-WIRE 8-SOIC |
| DS1722S/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1722S+ | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1722S+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 3-WIRE/SPI 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER DIG 3-WIRE 8-SOIC |
| DS1722S+T&R | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。