- 您現在的位置：買賣IC網 > PDF目錄97863 > DS1721S (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | DS1721S |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | 0.150 INCH, SOIC-8 |
| 文件頁數： | 18/19頁 |
| 文件大?。?/td> | 356K |
| 代理商： | DS1721S |
DS1721
8 of 17
DATA TRANSFER ON 2-WIRE SERIAL BUS Figure 5
Figure 6 details how data transfer is accomplished on the two-wire bus. Depending upon the state of the
R/ W bit, two types of data transfer are possible:
Data transfer from a master transmitter to a slave receiver. The 1st byte transmitted by the master is
the slave address. Next follows a number of data bytes. The slave returns an acknowledge bit after each
received byte.
Data transfer from a slave transmitter to a master receiver. The 1st byte (the slave address) is
transmitted by the master. The slave then returns an acknowledge bit. Next follows a number of data
bytes transmitted by the slave to the master. The master returns an acknowledge bit after all received
bytes other than the last byte. At the end of the last received byte, a ‘not acknowledge’ is returned.
The master device generates all of the serial clock pulses and the START and STOP conditions. A
transfer is ended with a STOP condition or with a repeated START condition. Since a repeated START
condition is also the beginning of the next serial transfer, the bus will not be released.
The DS1721 may operate in the following two modes:
Slave receiver mode: Serial data and clock are received through SDA and SCL. After each byte is
received, an acknowledge bit is transmitted. START and STOP conditions are recognized as the
beginning and end of a serial transfer. Address recognition is performed by hardware after reception of
the slave address and direction bit.
Slave transmitter mode: The first byte is received and handled as in the slave receiver mode. However,
in this mode, the direction bit will indicate that the transfer direction is reversed. Serial data is transmitted
on SDA by the DS1721 while the serial clock is input on SCL. START and STOP conditions are
recognized as the beginning and end of a serial transfer.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1722S/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS1722U | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS1722S+ | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| MAX6708 | 低電壓、SOT23封裝、微處理器監控電路，帶有電源失效檢測輸入/輸出、手動復位及看門狗定時器 |
| DS1726U/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1721S/T&R | 制造商:Maxim Integrated Products 功能描述:2-WIRE DIGITAL THERMOMETER SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG HP 8SOIC |
| DS1721S/T&R+W | 制造商:Maxim Integrated Products 功能描述:DIGITAL THERMOMETER AND THERMOSTAT - Tape and Reel |
| DS1721S/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1721S/T,R | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2-Wire Digital Thermometer and Thermostat |
| DS1721S+ | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。