- 您現在的位置：買賣IC網 > PDF目錄376958 > DS1721 2-Wire Digital Thermometer and Thermostat PDF資料下載
參數資料
| 型號： | DS1721 |
| 英文描述： | 2-Wire Digital Thermometer and Thermostat |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 210K |
| 代理商： | DS1721 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
DS1721
6 of 16
R0, R1
= Thermometer Resolution Bits. Table 3 below defines the resolution of the digital thermometer,
based on the settings of these two bits. There is a direct tradeoff between resolution and conversion time,
as depicted in the DC Electrical Characteristics: Digital Thermometer table. The designer has read/write
access to R0 and R1, and the default state is R0="1" and R1="1" (12-bit conversions).
THERMOMETER RESOLUTION CONFIGURATION
Table 3
R1
0
0
1
1
R0
0
1
0
1
THERMOMETER
RESOLUTION
9-BIT
10-BIT
11-BIT
12-BIT
MAX
CONVERSION
TIME
0.15s
0.3s
0.6s
1.2s
X
= Undefined. These bits are used internally by the DS1721.
DONE
= Temperature Conversion Status Bit. "1" = conversion complete and "0" = conversion in
progress. The DONE bit is read-only, and the power-up state is "1". In the continuous conversion mode,
DONE = "0".
Thermostat Setpoints Programming
The thermostat registers (TH and TL) define the setpoints for operation of the TCOM output. The
respective register can be accessed over the 2-wire bus via the Access TH (A1h) or Access TL (A2h)
commands. Reading from or writing to the respective register is controlled by the state of the R/
W
bit in
the 2-wire control byte (See “2-Wire Serial Data Bus” section).
The format of the TH and TL registers is a 12-bit 2’s complement representation of the temperature in °C.
The user can program the number of bits (9, 10, 11, or 12) for each TH and TL that correspond to the
thermometer resolution configuration chosen. If the 9-bit mode is chosen, for example, the 3 least
significant bits of TH and TL will be ignored by the thermostat comparator. The format for both TH and
TL is shown in Figure 4. The power-up default of TH is 80°C and that for TL is 75°C.
TEMPERATURE/DATA RELATIONSHIPS
Figure 4
S
2
6
2
5
MSb
2
-1
2
-2
2
-3
2
4
(UNIT = °C)
2
-4
2
3
2
2
2
1
2
0
LSb
0
MSB
0
0
0
LSB
TEMP
DIGITAL OUTPUT
(Binary)
0101 0000 0000 0000
0100 1011 0000 0000
0000 1010 0010 0000
0000 0000 1000 0000
0000 0000 0000 0000
1111 1111 1000 0000
1111 0101 1110 0000
1110 0110 1111 0000
1100 1001 0000 0000
DIGITAL OUTPUT
(Hex)
5000h
4B00h
0A20h
0080h
0000h
FF80h
F5E0h
E6F0h
C900h
+80°C
+75°C
+10.125°C
+0.5°C
+0°C
-0.5°C
-10.125°C
-25.0625°C
-55°C
相關PDF資料 |
PDF描述 |
|---|---|
| DS1722S | IC-SM-DIGITAL THERMOMETER |
| DS1722 | Digital Thermometer with SPI/3-Wire Interface |
| DS1730Y-150 | NVRAM (Battery Based) |
| DS1730Y-150-IND | NVRAM (Battery Based) |
| DS1730Y-200 | NVRAM (Battery Based) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1721S | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1721S/T&R | 制造商:Maxim Integrated Products 功能描述:2-WIRE DIGITAL THERMOMETER SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG HP 8SOIC |
| DS1721S/T&R+W | 制造商:Maxim Integrated Products 功能描述:DIGITAL THERMOMETER AND THERMOSTAT - Tape and Reel |
| DS1721S/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1721S/T,R | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2-Wire Digital Thermometer and Thermostat |
發布緊急采購，3分鐘左右您將得到回復。