- 您現在的位置：買賣IC網 > PDF目錄97863 > DS1720S+T&R (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | DS1720S+T&R |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), RECTANGULAR, SURFACE MOUNT |
| 封裝： | 0.208 INCH, LEAD FREE, SOIC-8 |
| 文件頁數： | 13/14頁 |
| 文件大小： | 173K |
| 代理商： | DS1720S+T&R |
DS1720
8 of 14
Read TH [A1h]
This command reads the value of the TH (HIGH TEMPERATURE) register. After issuing this command,
the next nine clock cycles clock out the 9–bit temperature limit which sets the threshold for operation of
the THIGH output.
Read TL [A2h]
This command reads the value of the TL (LOW TEMPERATURE) register. After issuing this command,
the next nine clock cycles clock out the 9–bit temperature limit which sets the threshold for operation of
the TLOW output.
Read Counter [A0h]
This command reads the value of the counter byte. The next nine clock cycles will output the contents of
this register.
Read Slope [A9h]
This command reads the value of the slope counter byte from the DS1720. The next nine clock cycles
will output the contents of this register.
Start Convert T [EEh]
This command begins a temperature conversion. No further data is required. In one–shot mode, the
temperature conversion will be performed and then the DS1720 will remain idle. In continuous mode, this
command will initiate continuous conversions.
Stop Convert T [22h]
This command stops temperature conversion. No further data is required. This command may be used to
halt a DS1720 in continuous conversion mode. After issuing this command, the current temperature
measurement will be completed, and then the DS1720 will remain idle until a Start Convert T is issued to
resume continuous operation.
Write Config [0Ch]
This command writes to the configuration register. After issuing this command, the next eight clock
cycles clock in the value of the configuration register.
Read Config [ACh]
This command reads the value in the configuration register. After issuing this command, the next eight
clock cycles output the value of the configuration register.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1720S+ | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), RECTANGULAR, SURFACE MOUNT |
| DS1720S | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), RECTANGULAR, SURFACE MOUNT |
| DS1721S+T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT |
| DS1721U+ | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| DS1721U | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1720STR | 制造商:Maxim Integrated Products 功能描述: |
| DS1721 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:2-Wire Digital Thermometer and Thermostat |
| DS1721S | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1721S/T&R | 制造商:Maxim Integrated Products 功能描述:2-WIRE DIGITAL THERMOMETER SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG HP 8SOIC |
| DS1721S/T&R+W | 制造商:Maxim Integrated Products 功能描述:DIGITAL THERMOMETER AND THERMOSTAT - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。