- 您現在的位置：買賣IC網 > PDF目錄9406 > DS1682S+ (Maxim Integrated Products)IC TIMEKEEPER ALARM ELAPSE 8SOIC PDF資料下載
參數資料
| 型號： | DS1682S+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/14頁 |
| 文件大小： | 0K |
| 描述： | IC TIMEKEEPER ALARM ELAPSE 8SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 類型： | 耗用時間計數器 |
| 特點： | 警報器，EEPROM |
| 存儲容量： | 10B |
| 時間格式： | 二進制 |
| 數據格式： | 二進制 |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 2.5 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1434 (CN2011-ZH PDF) |
Depending upon the state of the R/W bit, two types of
data transfer are possible:
Data transfer from a master transmitter to a slave
receiver. The first byte transmitted by the master is the
slave address. Next follows a number of data bytes. The
slave returns an acknowledge bit after each received
byte.
Data transfer from a slave transmitter to a master
receiver. The master transmits the first byte (the slave
address). The slave then returns an acknowledge bit. Next
follows a number of data bytes transmitted by the slave to
the master. The master returns an acknowledge bit after
all received bytes other than the last byte. A “not acknowl-
edge” is returned at the end of the last received byte.
The master device generates all of the serial clock pulses
and the START and STOP conditions. A transfer is ended
with a STOP condition or with a repeated START condi-
tion. Since a repeated START condition is also the begin-
ning of the next serial transfer, the bus is not released.
Slave Receiver Mode (Write Mode): Serial data and
clock are received through SDA and SCL. After each byte
is received, the receiver transmits an acknowledge bit.
START and STOP conditions are recognized as the begin-
ning and end of a serial transfer. The slave address byte is
the first byte received after the master generates a START
condition. The address byte contains the 7-bit DS1682
address, which is 1101011 (D6h), followed by the direction
bit (R/W). The second byte from the master is the register
address. This sets the register pointer. The master then
transmits each byte of data, with the DS1682 acknowledg-
ing each byte received. The register pointer increments
after each byte is written. The master generates a STOP
condition to terminate the data write (Figure 7).
Slave Transmitter Mode (Read Mode): The first byte
is received and handled as in the slave receiver mode.
However, in this mode, the direction bit indicates that the
transfer direction is reversed. Serial data is transmitted on
SDA by the DS1682 while the serial clock is input on SCL.
The slave address byte is the first byte received after the
master generates a START condition. The address byte
contains the 7-bit DS1682 address, followed by the direc-
tion bit (R/W). After receiving a valid slave address byte
and direction bit, the DS1682 generates an acknowledge
on the SDA line. The DS1682 begins to transmit data on
each SCL pulse starting with the register address pointed
to by the register pointer. As the master reads each byte,
it must generate an acknowledge. The register pointer
increments after each byte is read. The DS1682 must
receive a “not acknowledge” on the last byte to end a
read (Figure 8).
Figure 7. Data Write—Slave Receiver Mode
Figure 8. Data Read—Slave Transmitter Mode
R/W
R/W – READ/WRITE OR DIRECTION BIT
S
1101011
0
A
XXXXXXXX
A
XXXXXXXX
A
XXXXXXXX
A
XXXXXXXX
P
DATA TRANSFERRED
(X + 1 BYTES + ACKNOWLEDGE)
SLAVE
ADDRESS
REGISTER
ADDRESS
S – START
A – ACKNOWLEDGE
P – STOP
DATA (n)
DATA (n + 1)
DATA (n + x)
R/W
/A – NOT ACKNOWLEDGE
S
1101011
1
A
XXXXXXXX
A
XXXXXXXX
A
XXXXXXXX
A
XXXXXXXX
/A
DATA TRANSFERRED
(X + 1 BYTES + ACKNOWLEDGE)
SLAVE
ADDRESS
S – START
A – ACKNOWLEDGE
P – STOP
DATA (n + 1)
DATA (n)
DATA (n + 2)
DATA (n + x)
R/W – READ/WRITE OR DIRECTION BIT
DS1682
Total-Elapsed-Time Recorder
with Alarm
www.maximintegrated.com
Maxim Integrated │ 12
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/26FE8PB | CONN PLUG 8POS STRAIGHT W/PINS |
| MS27474T22A55P | CONN RCPT 55POS JAM NUT W/PINS |
| MS27467E23F35PC | CONN PLUG 100POS STRAIGHT W/PINS |
| MS27466E23A53S | CONN RCPT 53POS WALL MT W/SCKT |
| VI-22M-MX-B1 | CONVERTER MOD DC/DC 10V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1682S/GG8 | 制造商:Maxim Integrated Products 功能描述: |
| DS1682S/T&R | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 10BYTE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TIMEKEEPER ALARM ELAPSE 8SOIC |
| DS1682S/T&R | 功能描述:實時時鐘 Total-Elapsed-Time Recorder w/Alarm RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1682S/TR | 制造商:Maxim Integrated Products 功能描述: |
| DS1682S+ | 功能描述:實時時鐘 Total-Elapsed-Time Recorder w/Alarm RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。