- 您現在的位置：買賣IC網 > PDF目錄9404 > DS1677E+ (Maxim Integrated Products)IC CTRLR SYSTEM PORT 20-TSSOP PDF資料下載
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
DS1677
10 of 18
CU BIT TIMING Figure 5
3-WIRE SERIAL INTERFACE
Communication with the DS1677 is accomplished through a simple 3-wire interface consisting of the
Chip Select (CS), Serial Clock (SCLK) and Input/Output (I/O) pins.
All data transfers are initiated by driving the CS input high. The CS input serves two functions. First, CS
turns on the control logic, which allows access to the shift register for the address/command sequence.
Second, the CS signal provides a method of terminating either single byte or multiple byte (burst) data
transfer. A clock cycle is a sequence of a rising edge followed by a falling edge. For data input, data must
be valid during the rising edge of the clock and data bits are output on the falling edge of the clock. If the
CS input goes low, all data transfer terminates and the I/O pin goes to a high impedance state.
Address and data bytes are always shifted LSB first into the I/O pin. Any transaction requires the
address/command byte to specify a read or write to a specific register followed by one or more bytes of
data. The address byte is always the first byte entered after CS is driven high. The most significant bit
( RD /WR) of this byte determines if a read or write will take place. If this bit is 0, one or more read cycles
will occur. If this bit is 1, one or more write cycles will occur.
Data transfers can occur one byte at a time or in multiple byte burst mode. After CS is driven high an
address is written to the DS1677. After the address, one or more data bytes can be read or written. For a
single byte transfer one byte is read or written and then CS is driven low. For a multiple byte transfer,
multiple bytes can be read or written to the DS1677 after the address has been written. Each read or write
cycle causes the register address to automatically increment. Incrementing continues until the device is
disabled. After accessing register 0Eh, the address wraps to 00h.
Data transfer for single byte transfer and multiple byte burst transfer is illustrated in Figures 6 and 7.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1673E-3+ | IC CTRLR SYSTEM PORT 3V 20-TSSOP |
| DS12CR887-33+ | IC RTC W/RAM 128 BYTE 24-EDIP |
| DS17285SN-5+ | IC RTC 5V 2K NV RAM 24-SOIC |
| DS17285SN-3+ | IC RTC 3V 2K NV RAM 24-SOIC |
| MCP4641T-103E/ML | IC DGTL POT 10K 256TAPS 16-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1677E+ | 功能描述:實時時鐘 Portable System Controller RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1677E-5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Portable System Controller(275.85 k) |
| DS1678 | 功能描述:實時時鐘 Real-Time Event Recorder RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1678+ | 功能描述:實時時鐘 Real-Time Event Recorder RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1678J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2-Input Digital Multiplexer |
發布緊急采購，3分鐘左右您將得到回復。