- 您現在的位置：買賣IC網 > PDF目錄97862 > DS1672U-33 (MAXIM INTEGRATED PRODUCTS INC) 0 TIMER(S), REAL TIME CLOCK, PDSO8 PDF資料下載
參數資料
| 型號： | DS1672U-33 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Timer or RTC |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封裝： | 3 MM, MICRO, SOP-8 |
| 文件頁數： | 4/15頁 |
| 文件大?。?/td> | 283K |
| 代理商： | DS1672U-33 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
DS1672
12 of 15
I
2C Serial Data Bus
The DS1672 supports a bidirectional I
2C bus and data transmission protocol. A device that sends data
onto the bus is defined as a transmitter and a device receiving data as a receiver. The device that controls
the message is called a master. The devices that are controlled by the master are slaves. The bus must be
controlled by a master device that generates the serial clock (SCL), controls the bus access, and generates
the START and STOP conditions. The DS1672 operates as a slave on the I
2C bus. Connections to the bus
are made via the open-drain I/O lines SDA and SCL. Within the bus specifications, a standard mode
(100kHz maximum clock rate) and a fast mode (400kHz maximum clock rate) are defined. The DS1672
operates in both modes.
The following bus protocol has been defined (Figure 6):
Data transfer may be initiated only when the bus is not busy.
During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in
the data line while the clock line is high will be interpreted as control signals.
Accordingly, the following bus conditions have been defined:
Bus not busy: Both data and clock lines remain HIGH.
Start data transfer: A change in the state of the data line from high to low, while the clock line is
high, defines a START condition.
Stop data transfer: A change in the state of the data line from low to high, while the clock line is
high, defines a STOP condition.
Data valid: The state of the data line represents valid data when, after a START condition, the
data line is stable for the duration of the high period of the clock signal. The data on the line must
be changed during the low period of the clock signal. There is one clock pulse per bit of data.
Each data transfer is initiated with a START condition and terminated with a STOP condition.
The number of data bytes transferred between the START and the STOP conditions is not limited,
and is determined by the master device. The information is transferred byte-wise and each
receiver acknowledges with a ninth bit. Within the I
2C bus specifications a standard mode
(100kHz clock rate) and a fast mode (400kHz clock rate) are defined.
Acknowledge: Each receiving device, when addressed, is obliged to generate an acknowledge
after the reception of each byte. The master device must generate an extra clock pulse that is
associated with this acknowledge bit.
A device that acknowledges must pull down the SDA line during the acknowledge clock pulse in
such a way that the SDA line is stable LOW during the HIGH period of the acknowledge related
clock pulse. Of course, setup and hold times must be taken into account. A master must signal an
end of data to the slave by not generating an acknowledge bit on the last byte that has been
clocked out of the slave. In this case, the slave must leave the data line HIGH to enable the master
to generate the STOP condition.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1672S-2 | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| DS1672U-3 | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| DS1672S-3 | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| DS1673S-3 | 0 TIMER(S), REAL TIME CLOCK, PDSO20 |
| DS1673E-5 | 0 TIMER(S), REAL TIME CLOCK, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1672U-33/T&R | 功能描述:實時時鐘 I2C 32-Bit Binary Counter RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1672U-33/TR | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:I2C 32-Bit Binary Counter RTC |
| DS1672U-33+ | 功能描述:實時時鐘 I2C 32-Bit Binary Counter RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1672U-33+T&R | 制造商:Maxim Integrated Products 功能描述:32 BIT COUNTER-USOP 3.3V T&R LFREE 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 8USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 8USOP - Cut TR (SOS) 制造商:Maxim Integrated Products 功能描述:Maxim Integrated DS1672U-33+T&R Real Time Clocks (RTC) 制造商:Maxim Integrated Products 功能描述:IC TIMEKEEPER 3.3V 32-BIT 8-USOP 制造商:Maxim Integrated Products 功能描述:Real Time Clock I2C 32-Bit Binary Counter RTC |
| DS1672U-33+T&R | 功能描述:實時時鐘 I2C 32-Bit Binary Counter RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。