switch by pulling the RST line low. After the internal 250ms timer has e" />
參數資料
型號: DS1670S
廠商: Maxim Integrated Products
文件頁數: 15/16頁
文件大小: 0K
描述: IC CTRLR SYSTEM PORTABLE 20-SOIC
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 37
類型: 便攜系統(tǒng)控制器
特點: 警報器,閏年,監(jiān)視計時器
時間格式: HH:MM:SS(12/24 小時)
數據格式: YY-MM-DD-dd
接口: 3 線串口
電源電壓: 2.97 V ~ 3.63 V
電壓 - 電源,電池: 2.5 V ~ 3.7 V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 20-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 20-SOIC W
包裝: 管件
DS1670
8 of 16
switch by pulling the RST line low. After the internal 250ms timer has expired, the DS1670 will continue
to monitor the RST line. If the line is still low, the DS1670 will continue to monitor the line looking for a
rising edge. Upon detecting release, the DS1670 will force the RST line low and hold it low for 250ms.
The third microprocessor monitoring function provided by the DS1670 is a watchdog timer. The
watchdog timer function forces RST to the active state when the ST input is not stimulated within the
predetermined time period. The time period is set by the Time Delay (TD) bits in the Watchdog Register.
The time delay can be set to 250ms, 500ms, or 1000ms (see Figure 5). If TD0 and TD1 are both set to 0,
the watchdog timer is disabled. When enabled, the watchdog timer starts timing out from the set time
period as soon as RST is inactive. The default setting is for the watchdog timer to be enabled with
1000ms time delay. If a high-to-low transition occurs on the ST input pin prior to timeout, the watchdog
timer is reset and begins to time-out again. If the watchdog timer is allowed to timeout, then the RST
signal is driven to the active state for 250ms (typical). The ST input can be derived from microprocessor
address signals, data signals, and/or control signals. To guarantee that the watchdog timer does not
timeout, a high-to-low transition must occur at or less than the minimum period.
WATCHDOG TIMEOUT CONTROL Figure 5
WATCHDOG REGISTER
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0
TD1
TD0
WATCHDOG TIMEOUT
TD1
TD0
WATCHDOG TIMEOUT
0
Watchdog disabled
0
1
250ms
1
0
500ms
1
1000ms
ANALOG-TO-DIGITAL CONVERTER
The DS1670 provides a 3-channel, 8-bit analog-to-digital converter. The ADC reference voltage (2.55V
typical) is derived from an on-chip band-gap circuit. Three multiplexed analog inputs are provided
through the AIN0, AIN1, and AIN2 pins. The ADC is monotonic (no missing codes) and uses a
successive approximation technique to convert the analog signal into a digital code. An A/D conversion is
the process of assigning a digital code to an analog input voltage. This code represents the input value as
a fraction of the full-scale voltage (FSV) range. Thus, the FSV range is then divided by the ADC into 256
codes (8 bits). The FSV range is bounded by an upper limit equal to the reference voltage and the lower
limit, which is ground. The DS1670 has a FSV of 2.55V (typical) that provides a resolution of 10mV. An
input voltage equal to the reference voltage converts to FFh while an input voltage equal to ground
converts to 00h. The relative linearity of the ADC is ±0.5 LSB.
The ADC selects from one of three different analog inputs (AIN0–AIN2). The input that is selected is
determined by the Analog Input Select (AIS) bits in the Control Register. Table 2 lists the specific analog
相關PDF資料
PDF描述
DS1672S-3/T&R IC TIMEKEEPER 3V 32-BIT 8-SOIC
DS1673S-3 IC CTRLR SYSTEM PORT 3V 20-SOIC
DS1677E IC CTRLR SYSTEM PORT 20-TSSOP
DS1678S/T&R IC RECORDER REALTIME EVENT 8SOIC
DS1682S IC TIMEKEEPER ALARM ELAPSE 8SOIC
相關代理商/技術參數
參數描述
DS1670S+ 功能描述:實時時鐘 Portable System Controller RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS1671H 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Clock Driver
DS1671J-8 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Clock Driver
DS-1671ZJ 制造商:Hikvision USA 功能描述:4" Indoor Ceiling Embedded Mount
DS1672 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Low Voltage Serial Timekeeping Chip