• <form id="0fphd"></form>
    <code id="0fphd"></code>
    參數資料
    型號: DS1669-100
    廠商: Maxim Integrated Products
    文件頁數: 2/11頁
    文件大?。?/td> 0K
    描述: IC RHEOSTAT DALLASTAT 100K 8-DIP
    標準包裝: 50
    系列: Dallastat™
    接片: 64
    電阻(歐姆): 100k
    電路數: 1
    溫度系數: 標準值 750 ppm/°C
    存儲器類型: 非易失
    接口: 上/下
    電源電壓: ±4.5 V ~ 8 V
    工作溫度: -40°C ~ 85°C
    安裝類型: 通孔
    封裝/外殼: 8-DIP(0.300",7.62mm)
    供應商設備封裝: 8-PDIP
    包裝: 管件
    其它名稱: DS1669100
    DS1669
    10 of 10
    NOTES:
    1. All inputs; UV, DC, and D are internally pulled up with a resistance of 100k.
    2. Input logic levels are referenced to -V.
    3. ICC is the internal current that flows between -V and +V.
    4. Input leakage applies to contact inputs UC and DC and digital input (D).
    5. Wiper current and rheostat currents are the maximum currents which can flow in the resistive
    elements.
    6. Capacitance values apply at 25°C.
    7. Input pulse width is the minimum time required for an input to cause an increment or decrement. If
    the UC, DC or D input is held active for longer than 1 second, subsequent increments or decrements
    will occur on 100 ms intervals until the inputs UC, DC, and/or D is released to VIH.
    8. Repetitive pulsed inputs on UC, DC, or D will be recognized as long as the pulse repetition occurs
    within 1 second of each other. Pulses occurring faster than 1 ms apart may not be recognized as
    individual inputs but can be interpreted a constant input.
    9. Idle state supply current is measured with no pushbutton depressed and with the wiper. RW tied to a
    CMOS load.
    10. Maximum time required for the Dallastat to determine single or dual pushbutton operation after input
    supply has reached 10% of recommended supply operating conditions.
    11. Absolute linearity is used to determine wiper voltage versus expected voltage as determined by wiper
    position.
    12. Relative linearity is used to determine the change in voltage between successive tap positions.
    13. -3 dB cutoff frequency characteristics for the DS1669 depend on potentiometer total resistance:
    DS1669-010; 1 MHz, DS1669-050; 200 kHz, DS1669-100; 100 kHz.
    14. Valid at 25
    °C only.
    相關PDF資料
    PDF描述
    VE-BW2-MV-S CONVERTER MOD DC/DC 15V 150W
    MS27468E23B2P CONN RCPT 85POS JAM NUT W/PINS
    MS27467T23B2PC CONN PLUG 85POS STRAIGHT W/PINS
    ICS9112AG-16LFT IC BUFFER ZD HI PERFORM 8-TSSOP
    GTC02R-28-21P CONN RCPT 37POS BOX MNT W/PINS
    相關代理商/技術參數
    參數描述
    DS1669-100+ 功能描述:數字電位計 IC Dallastat 100K Rheostat RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
    DS1669-50 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
    DS1669-50+ 功能描述:數字電位計 IC Dallastat 50K Rheostat RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
    DS1669E-50/T&R/ 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
    DS1669N-10 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital Potentiometer