- 您現在的位置：買賣IC網 > Datasheet目錄39 > DS1631S+T&R (Maxim Integrated)IC THERMOMETER DIG HI-PREC 8SOIC Datasheet資料下載
參數資料
| 型號： | DS1631S+T&R |
| 廠商： | Maxim Integrated |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 435K |
| 描述： | IC THERMOMETER DIG HI-PREC 8SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 功能： | 溫度計，恒溫計 |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 125°C |
| 精確度： | ±2°C（最小值） |
| 拓撲： | ADC（三角積分型），比較器，寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 無 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
DS1631/DS1631A/DS1731
11 of 15
2-WIRE SERIAL DATA BUS
The DS1631, DS1631A, and DS1731 communicate over a bidirectional 2-wire serial data bus that
consists of a serial clock (SCL) signal and serial data (SDA) signal. The DS1631, DS1631A, and DS1731
interface to the bus through their SCL input pins and open-drain SDA I/O pins.
The following terminology is used to describe 2-wire communication:
Master Device: Microprocessor/microcontroller that controls the slave devices on the bus. The master
device generates the SCL signal and START and STOP conditions.
Slave: All devices on the bus other than the master. The DS1631, DS1631A, and DS1731 always
function as slaves.
Bus Idle or Not Busy: Both SDA and SCL remain high. SDA is held high by a pullup resistor when the
bus is idle, and SCL must either be forced high by the master (if the SCL output is push-pull) or pulled
high by a pullup resistor (if the SCL output is open-drain).
Transmitter: A device (master or slave) that is sending data on the bus.
Receiver: A device (master or slave) that is receiving data from the bus.
START Condition: Signal generated by the master to indicate the beginning of a data transfer on the
bus. The master generates a START condition by pulling SDA from high to low while SCL is high (see
Figure 8). A repeated START is sometimes used at the end of a data transfer (instead of a STOP) to
indicate that the master will perform another operation.
STOP Condition: Signal generated by the master to indicate the end of a data transfer on the bus. The
master generates a STOP condition by transitioning SDA from low to high while SCL is high (see Figure
8). After the STOP is issued, the master releases the bus to its idle state.
Acknowledge (ACK): When a device is acting as a receiver, it must generate an acknowledge (ACK) on
the SDA line after receiving every byte of data. The receiving device performs an ACK by pulling the
SDA line low for an entire SCL period (see Figure 8). During the ACK clock cycle, the transmitting
device must release SDA. A variation on the ACK signal is the not acknowledge (NACK). When the
master device is acting as a receiver, it uses a NACK instead of an ACK after the last data byte to indicate
that it is finished receiving data. The master indicates a NACK by leaving the SDA line high during the
ACK clock cycle.
Slave Address: Every slave device on the bus has a unique 7-bit address that allows the master to access
that device. The 7-bit bus address is 1 0 0 1 A
2
A
1
A
0
, where A
2
, A
1
, and A
0
are user-selectable through
the corresponding input pins. The three address pins allow up to eight DS1631s, DS1631As, or DS1731s
to be multidropped on the same bus.
Control Byte: The control byte is transmitted by the master and consists of the 7-bit slave address plus a
read/write (R/W?/SPAN>?/SPAN>) bit (see Figure 7). If the master is going to read data from the slave device then R/W?/SPAN>?/SPAN> =
1, and if the master is going to write data to the slave device then R/W?/SPAN>?/SPAN> = 0.
Command Byte: Te command byte can be any of the command protocols described in the COMMAND
SET section of this data sheet.
Figure 7. CONTROL BYTE
bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0
1
0
0
1
A
2
A
1
A
0
R/W?/SPAN>?/SPAN>
相關PDF資料 |
PDF描述 |
|---|---|
| DS1721U+T&R | IC THERMOMETER/STAT DIG HP 8USOP |
| DS1722S | IC THERMOMETER DIG 3-WIRE 8-SOIC |
| DS1775R7+T&R | IC THERMOM/STAT DIG 111 SOT-23-5 |
| DS1821C+ | IC THERMOMETER/STAT PROG 3-TO92 |
| DS1825U+T&R | IC THERMOMETER DIGITAL 8-USOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1631U | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1631U/T&R | 制造商:Maxim Integrated Products 功能描述:0.5C 12C TEMP SENSOR MSOP T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER DIG HI-PREC 8MSOP |
| DS1631U/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1631U/TR | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision Digital Thermometer and Thermostat |
| DS1631U+ | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。