- 您現在的位置：買賣IC網 > PDF目錄376955 > DS1631AU High-Precision Digital Thermometer and Thermostat PDF資料下載
參數資料
| 型號： | DS1631AU |
| 元件分類： | 溫度傳感器 |
| 英文描述： | High-Precision Digital Thermometer and Thermostat |
| 中文描述： | 高精度數字溫度計和溫度 |
| 文件頁數： | 17/19頁 |
| 文件大?。?/td> | 288K |
| 代理商： | DS1631AU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁
DS1244/DS1244P
17 of 19
AC TEST CONDITIONS
Output Load:
Input Pulse Levels:
50pF + 1TTL Gate
0 to 3V
Timing Measurement Reference Levels
Input:
1.5V
Output:
1.5V
Input Pulse Rise and Fall Times: 5ns
NOTES:
1)
WE is high for a read cycle.
2)
OE = V
IH
or V
IL
. If OE = V
IH
during write cycle, the output buffers remain in a high-impedance
state.
3)
t
WP
is specified as the logical AND of CE and WE. t
WP
is measured from the latter of CE or WE
going low to the earlier of CE or WE going high.
4)
t
DH
, t
DS
are measured from the earlier of CE or WE going high.
5)
These parameters are sampled with a 50pF load and are not 100% tested.
6)
If the CE low transition occurs simultaneously with or later than the WE low transition in Write
Cycle 1, the output buffers remain in a high-impedance state during this period.
7)
If the CE high transition occurs prior to or simultaneously with the WE high transition, the output
buffers remain in a high-impedance state during this period.
8)
If WE is low or the WE low transition occurs prior to or simultaneously with the CE low transition,
the output buffers remain in a high impedance state during this period.
9)
The expected t
DR
is defined as cumulative time in the absence of V
CC
with the clock oscillator
running.
10)
t
WR
is a function of the latter occurring edge of WE or CE.
11)
Voltages are referencd to ground.
12)
RST (Pin 1) has an internal pullup resistor.
13)
RTC modules can be successfully processed through conventional wave-soldering techniques as long
as temperature exposure to the lithium energy source contained within does not exceed +85°C. Post-
solder cleaning with water-washing techniques is acceptable, provided that ultrasonic vibration is not
used.
In addition, for the PowerCap:
1)
Dallas Semiconductor recommends that PowerCap module bases experience one pass through solder
reflow oriented with the label side up (“l(fā)ive-bug”).
2)
Hand soldering and touch-up: Do not touch or apply the soldering iron to leads for more than three
seconds.
–
To solder, apply flux to the pad, heat the lead frame pad, and apply solder. To remove the part,
apply flux, heat the lead frame pad until the solder reflows, and use a solder wick to remove
solder.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1631U | High-Precision Digital Thermometer and Thermostat |
| DS1631Z | High-Precision Digital Thermometer and Thermostat |
| DS1642-12 | Real-Time Clock |
| DS1642-120 | IC-16K CMOS NVRAM |
| DS1642-15 | Real-Time Clock |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1631AU/T&R | 制造商:Maxim Integrated Products 功能描述:0.5C 12C ACTIVE POWER-UP DS1631U - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER DIG HI-PREC 8USOP |
| DS1631AU/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1631AU/TR | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision Digital Thermometer and Thermostat |
| DS1631AU+ | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1631AU+ | 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER 0.5 ?SOP-8 |
發布緊急采購，3分鐘左右您將得到回復。