- 您現在的位置：買賣IC網 > PDF目錄376955 > DS1631A High-Precision Digital Thermometer and Thermostat PDF資料下載
參數資料
| 型號： | DS1631A |
| 英文描述： | High-Precision Digital Thermometer and Thermostat |
| 中文描述： | 高精度數字溫度計和溫度監控器 |
| 文件頁數： | 4/19頁 |
| 文件大?。?/td> | 288K |
| 代理商： | DS1631A |
DS1244/DS1244P
4 of 19
the
CE
and
OE
control of the phantom clock starts the pattern recognition sequence by moving a pointer
to the first bit of the 64-bit comparison register. Next, 64 consecutive write cycles are executed using the
CE
and
WE
control of the SmartWatch. These 64 write cycles are used only to gain access to the
phantom clock. Therefore, any address to the memory in the socket is acceptable. However, the write
cycles generated to gain access to the phantom clock are also writing data to a location in the mated
RAM. The preferred way to manage this requirement is to set aside just one address location in RAM as a
phantom clock scratch pad. When the first write cycle is executed, it is compared to bit 0 of the 64-bit
comparison register. If a match is found, the pointer increments to the next location of the comparison
register and awaits the next write cycle. If a match is not found, the pointer does not advance and all
subsequent write cycles are ignored. If a read cycle occurs at any time during pattern recognition, the
present sequence is aborted and the comparison register pointer is reset. Pattern recognition continues for
a total of 64 write cycles as described above until all the bits in the comparison register have been
matched (Figure 1). With a correct match for 64 bits, the phantom clock is enabled and data transfer to or
from the timekeeping registers can proceed. The next 64 cycles will cause the phantom clock to either
receive or transmit data on DQ0, depending on the level of the
OE
pin or the
WE
pin. Cycles to other
locations outside the memory block can be interleaved with
CE
cycles without interrupting the pattern
recognition sequence or data transfer sequence to the phantom clock.
PHANTOM CLOCK REGISTER INFORMATION
The phantom clock information is contained in eight registers of 8 bits, each of which is sequentially
accessed 1 bit at a time after the 64-bit pattern recognition sequence has been completed. When updating
the phantom clock registers, each register must be handled in groups of 8 bits. Writing and reading
individual bits within a register could produce erroneous results. These read/write registers are defined in
Figure 2.
Data contained in the phantom clock register is in binary coded decimal (BCD) format. Reading and
writing the registers is always accomplished by stepping through all eight registers, starting with bit 0 of
register 0 and ending with bit 7 of register 7.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1631AU | High-Precision Digital Thermometer and Thermostat |
| DS1631U | High-Precision Digital Thermometer and Thermostat |
| DS1631Z | High-Precision Digital Thermometer and Thermostat |
| DS1642-12 | Real-Time Clock |
| DS1642-120 | IC-16K CMOS NVRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1631A6B_BAA WAF | 制造商:Rochester Electronics LLC 功能描述: |
| DS1631AU | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1631AU/T&R | 制造商:Maxim Integrated Products 功能描述:0.5C 12C ACTIVE POWER-UP DS1631U - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER DIG HI-PREC 8USOP |
| DS1631AU/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1631AU/TR | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision Digital Thermometer and Thermostat |
發布緊急采購，3分鐘左右您將得到回復。