參數資料
型號： DS1631
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： Switch/Digital Output Temperature Sensor
英文描述： DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, THROUGH HOLE MOUNT
封裝： 0.300 INCH, PLASTIC, DIP-8
文件頁數： 4/15頁
文件大?。?/td> 196K
代理商： DS1631
DS1631/DS1631A/DS1731
12 of 15
Figure 8. START, STOP, AND ACK SIGNALS
GENERAL 2-WIRE INFORMATION
All data is transmitted MSb first over the 2-wire bus.
One bit of data is transmitted on the 2-wire bus each SCL period.
A pullup resistor is required on the SDA line and, when the bus is idle, both SDA and SCL must remain
in a logic-high state.
All bus communication must be initiated with a START condition and terminated with a STOP
condition. During a START or STOP is the only time SDA is allowed to change states while SCL is
high. At all other times, changes on the SDA line can only occur when SCL is low: SDA must remain
stable when SCL is high.
After every 8-bit (1-byte) transfer, the receiving device must answer with an ACK (or NACK), which
takes one SCL period. Therefore, nine clocks are required for every one-byte data transfer.
INITIATING 2-WIRE COMMUNICATION
To initiate 2-wire communication, the master generates a START followed by a control byte containing
the DS1631, DS1631A, or DS1731 slave address. The R/W
bit of the control byte must be a 0 (“write”)
since the master next writes a command byte. The DS1631/DS1631A/DS1731 responds with an ACK
after receiving the control byte. This must be followed by a command byte from the master, which
indicates what type of operation is to be performed. The DS1631/DS1631A/DS1731 again respond with
an ACK after receiving the command byte.
If the command byte is a Start Convert T or Stop Convert T command (see Figure 9a), the transaction is
finished, and the master must issue a STOP to signal the end of the communication sequence. If the
command byte indicates a write or read operation, additional actions must occur as explained in the
following sections.
2-WIRE WRITES
The master can write data to the DS1631/DS1631A/DS1731 by issuing an Access Config, Access TH, or
Access TL command following the control byte (see Figures 9b and 9d). Since the R/W
bit in the control
byte was a 0 (“write”), the DS1631/DS1631A/DS1731 are already prepared to receive data. Therefore,
after receiving an ACK in response to the command byte, the master device can immediately begin
transmitting data. When writing to the configuration register, the master must send one byte of data, and
when writing to the TH or TL registers the master must send two bytes of data. After receiving each data
byte, the DS1631/DS1631A/DS1731 respond with an ACK, and the transaction is finished with a STOP
from the master.
SCL
SDA
START
Condition
STOP
Condition
…
ACK (or NACK)
From Receiver
相關PDF資料
PDF描述
DS1631AU+ DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, SQUARE, SURFACE MOUNT
DS1631S DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT
DS1642-100 0 TIMER(S), REAL TIME CLOCK, PDIP24
DS1642-70 REAL TIME CLOCK, PDMA24
DS1643-100 1 TIMER(S), REAL TIME CLOCK, DMA28
相關代理商/技術參數
參數描述
DS1631 WAF 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述:
DS1631 WAF UP 制造商:Rochester Electronics LLC 功能描述:
DS1631+ 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1631A 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision Digital Thermometer and Thermostat
DS1631A6B_BAA WAF 制造商:Rochester Electronics LLC 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*