參數資料
型號: DS1626S+T&R
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: Switch/Digital Output Temperature Sensor
英文描述: DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT
封裝: LEAD FREE, SOIC-8
文件頁數: 3/16頁
文件大小: 217K
代理商: DS1626S+T&R
DS1626/DS1726
11 of 14
Table 5. CONFIGURATION REGISTER BIT DESCRIPTIONS
BIT NAME
(USER ACCESS)
FUNCTIONAL DESCRIPTION
DONE
(Read Only)
Power-up state = 1.
DONE = 0. Temperature conversion is in progress.
DONE = 1. Temperature conversion is complete.
THF
(Read/Write)
Power-up state = 0.
THF = 1. The measured temperature has reached or exceeded the value stored in
the TH register. THF will remain a 1 until it is overwritten with a 0 by the user,
the power is cycled, or a Software POR command is issued.
TLF
(Read/Write)
Power-up state = 0.
TLF = 1. The measured temperature has equaled or dropped below the value
stored in the TL register. TLF will remain a 1 until it is overwritten with a 0 by
the user, the power is cycled, or a Software POR command is issued.
NVB
(Read Only)
Power-up state = 0.
NVB = 1. Write to an E
2 memory cell is in progress.
NVB = 0. NV memory is not busy.
R1*
(Read/Write)
Power-up state = last value written to this bit.
Sets conversion resolution (see Table 6).
Initial state from factory = 1.
R0*
(Read/Write)
Power-up state = last value written to this bit.
Sets conversion resolution (see Table 6).
Initial state from factory = 1.
CPU*
(Read/Write)
Power-up state = last value written to this bit.
CPU = 1. Stand-alone mode is disabled.
CPU = 0. Stand-alone mode is enabled when RST = 0. See CPU BIT AND
STAND-ALONE THERMOSTAT OPERATION section for more information.
Initial state from factory = 0.
1SHOT*
(Read/Write)
Power-up state = last value written to this bit.
1SHOT = 1: One-Shot Mode. The Start Convert T command initiates a single
temperature conversion and then the device goes into a low-power standby state.
1SHOT = 0: Continuous Conversion Mode. The Start Convert T command
initiates continuous temperature conversions.
Initial state from factory = 0.
*NV (EEPROM)
Table 6. RESOLUTION CONFIGURATION
R1
R0
RESOLUTION
CONVERSION
TIME (MAX)
0
9-bit
93.75ms
0
1
10-bit
187.5ms
1
0
11-bit
375ms
1
12-bit
750ms
相關PDF資料
PDF描述
DS1629S 0 TIMER(S), REAL TIME CLOCK, PDSO8
DS1631S+ DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT
DS1631AU DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, SQUARE, SURFACE MOUNT
DS1631 DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, THROUGH HOLE MOUNT
DS1631AU+ DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, SQUARE, SURFACE MOUNT
相關代理商/技術參數
參數描述
DS1626U 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1626U/T&R 制造商:Maxim Integrated Products 功能描述:0.5C 3-WIRE DIG THERM (USOP) T&R - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:
DS1626U/T&R 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1626U+ 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1626U+T&R 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 3-WIRE 8USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-USOP 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Digital Thermometer & Thermostat