參數資料
型號: DS1626S+
廠商: Maxim Integrated
文件頁數: 8/12頁
文件大?。?/td> 141K
描述: IC THERMOMETER/STAT DIG 8-SOIC
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 1
功能: 溫度計,恒溫計
傳感器類型: 內部
感應溫度: -55°C ~ 125°C
精確度: ±2°C(最小值)
拓?fù)洌?/td> ADC(三角積分型),比較器,寄存器庫
輸出類型: 3 線串行
輸出警報:
輸出風扇: 無
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -55°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 8-SOIC(0.209",5.30mm 寬)
供應商設備封裝: 8-SOIC
包裝: 管件
DS1626/DS1726
 
 
8 of 12 
CPU BIT AND STAND-ALONE THERMOSTAT OPERATION 
In stand-alone thermostat mode, DS1626/DS1726 thermostat functionality can be used without requiring
a microcontroller to start/stop temperature conversions. The CPU bit in the configuration register
determines if stand-alone mode is enabled.
 
When CPU = 1 stand-alone mode is disabled, and the only way to start/stop temperature conversions is
by using a microcontroller to transmit Start Convert T and Stop Convert T commands, respectively.
 
Stand-alone mode is enabled when CPU = 0. In this mode, when RST = 0 the CLK/CNV pin operates as
a control signal to start and stop temperature measurements. Driving CLK/CNV low initiates continuous
temperature conversions that will continue until CLK/CNV is brought high again. If the CLK/CNV pin is
driven low and then returned to a high state in less than 10ms, only one temperature conversion will be
performed after which the DS1626/DS1726 will return to a low-power idle state (i.e., one-shot operation).
Note that when stand-alone mode is enabled, the 1SHOT bit in the configuration register is ignored, and
only the CLK/CNV signal determines whether continuous or one-shot conversions take place.
Since T
H
, T
L
, and the CPU bit are stored in EEPROM, the DS1626/DS1726 can be preprogrammed for
stand-alone operation. If desired, the CLK/CNV and RST pin can be connected to GND so the
DS1626/DS1726 will automatically begin taking temperature measurements at power-up
Normal bus communication with the DS1626/DS1726 can still take place in stand-alone mode when
RST = 1. When communication is initiated, stand-alone conversions are automatically halted. If during
the bus communication continuous temperature conversions are started using the Start Convert T
command, they can only be stopped by issuing a Stop Convert T command.  
 
Figure 5. THERMOSTAT OUTPUT OPERATION 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
T
L
 
T
H
 
TEMP
LOGIC 0
LOGIC 1
T
COM
 
TEMP
LOGIC 0
LOGIC 1
T
HIGH
 
TEMP
LOGIC 0
LOGIC 1
T
LOW
 
相關PDF資料
PDF描述
DS1629S+T&R IC THERM/RTC/CALENDAR DIG 8-SOIC
DS1631S+T&R IC THERMOMETER DIG HI-PREC 8SOIC
DS1721U+T&R IC THERMOMETER/STAT DIG HP 8USOP
DS1722S IC THERMOMETER DIG 3-WIRE 8-SOIC
DS1775R7+T&R IC THERMOM/STAT DIG 111 SOT-23-5
相關代理商/技術參數
參數描述
DS1626S+ 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1626S+T&R 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 3-WIRE 8USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC
DS1626S+T&R 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1626U 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1626U/T&R 制造商:Maxim Integrated Products 功能描述:0.5C 3-WIRE DIG THERM (USOP) T&R - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: