- 您現在的位置：買賣IC網 > Datasheet目錄39 > DS1624S+T&R (Maxim Integrated)IC THERM/EEPROM DIG 256BYT 8SOIC Datasheet資料下載
參數資料
| 型號： | DS1624S+T&R |
| 廠商： | Maxim Integrated |
| 文件頁數： | 4/18頁 |
| 文件大?。?/td> | 424K |
| 描述： | IC THERM/EEPROM DIG 256BYT 8SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 功能： | 溫度計，恒溫計 |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 125°C |
| 精確度： | ±0.5°C（最小值） |
| 拓?fù)洌?/td> | EEPROM，寄存器庫 |
| 輸出類型： | 2 線串行 |
| 輸出警報： | 無 |
| 輸出風扇： | 無 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 帶卷 (TR) |
DS1624
4 f 1
DATA TRANSFER ON 2-WIRE SERIAL BUS Figure 2
Figure 2 details how data transfer is accomplished on the two-wire bus. Depending upon the state of the
R/
bit, two types of data transfer are possible:
1. Data transfer from a master transmitter to a slave receiver. The first byte transmitted by the
master is the slave address. Next follows a number of data bytes. The slave returns an acknowledge
bit after each received byte.
2. Data transfer from a slave transmitter to a master receiver. The first byte (the slave address) is
transmitted by the master. The slave then returns an acknowledge bit. Next follows a number of data
bytes transmitted by the slave to the master. The master returns an acknowledge bit after all received
bytes other than the last byte. At the end of the last received byte, a not acknowledge is returned.
The master device generates all of the serial clock pulses and the START and STOP conditions. A
transfer is ended with a STOP condition or with a repeated START condition. Since a repeated START
condition is also the beginning of the next serial transfer, the bus will not be released.
The DS1624 may operate in the following two modes:
1. Slave receiver mode: Serial data and clock are received through SDA and SCL. After each byte is
received an acknowledge bit is transmitted. START and STOP conditions are recognized as the
beginning and end of a serial transfer. Address recognition is performed by hardware after reception
of the slave address and direction bit.
2. Slave transmitter mode: The first byte is received and handled as in the slave receiver mode.
However, in this mode the direction bit will indicate that the transfer direction is reversed. Serial data
is transmitted on SDA by the DS1624 while the serial clock is input on SCL. START and STOP
conditions are recognized as the beginning and end of a serial transfer.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1626S+ | IC THERMOMETER/STAT DIG 8-SOIC |
| DS1629S+T&R | IC THERM/RTC/CALENDAR DIG 8-SOIC |
| DS1631S+T&R | IC THERMOMETER DIG HI-PREC 8SOIC |
| DS1721U+T&R | IC THERMOMETER/STAT DIG HP 8USOP |
| DS1722S | IC THERMOMETER DIG 3-WIRE 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1625S | 制造商:Maxim Integrated Products 功能描述:DIGITAL THERMOMETER, 8 Pin, SOP |
| DS1626 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision 3-Wire Digital Thermometer and Thermostat |
| DS1626_07 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision 3-Wire Digital Thermometer and Thermostat |
| DS1626S | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1626S+ | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。