參數資料
型號: DS1620R
廠商: DALLAS SEMICONDUCTOR
元件分類: Switch/Digital Output Temperature Sensor
英文描述: DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), RECTANGULAR, SURFACE MOUNT
封裝: 0.300 INCH, SO-16
文件頁數: 9/11頁
文件大?。?/td> 17247K
代理商: DS1620R
DS1620R
7 of 11
102099
Stop Convert T [22h]
This command stops temperature conversion. No further data is required. This command may be used to
halt a DS1620R in continuous conversion mode. After issuing this command the current temperature
measurement will be completed and then the DS1620R will remain idle until a Start Convert T is issued
to resume continuous operation.
Write Config [0Ch]
This command writes to the configuration register. After issuing this command the next eight clock cycles
clock in the value of the configuration register.
Read Config [ACh]
This command reads the value in the configuration register. After issuing this command the next eight
clock cycles output the value of the configuration register.
DS1620R COMMAND SET Table 3
INSTRUCTION
DESCRIPTION
PROTOCOL
3-WIRE BUS
DATA AFTER
ISSUING
PROTOCOL
NOTES
TEMPERATURE CONVERSION COMMANDS
Read Temperature
Reads last converted temperature
value from temperature register.
Aah
<read data>
Start Convert T
Initiates temperature conversion.
Eeh
idle
1
Stop Convert T
Halts temperature conversion.
22h
idle
1
THERMOSTAT COMMANDS
Write TH
Writes high temperature limit value
into TH register.
01h
<write data>
2
Write TL
Writes low temperature limit value
into TL register.
02h
<write data>
2
Read TH
Reads stored value of high
temperature limit from TH register.
A1h
<read data>
2
Read TL
Reads stored value of low
temperature limit from TL register.
A2h
<read data>
2
Write Config
Writes configuration data to
configuration register.
0Ch
<write data>
2
Read Config
Reads configuration data from
configuration register.
ACh
<read data>
2
NOTES:
1. In continuous conversion mode, a Stop Convert T command will halt continuous conversion. To
restart, the Start Convert T command must be issued. In one–shot mode, a Start Convert T command
must be issued for every temperature reading desired.
2. Writing to the E
2 typically requires 10 ms at room temperature. After issuing a write command no
further writes should be requested for at least 10 ms.
相關PDF資料
PDF描述
DS1620 DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT
DS1620+ DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), RECTANGULAR, SURFACE MOUNT
DS1620S/T&R DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), RECTANGULAR, SURFACE MOUNT
DS1621S+T&R DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT
DS1621V+ DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), RECTANGULAR, SURFACE MOUNT
相關代理商/技術參數
參數描述
DS1620S 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1620S/T&R 制造商:Maxim Integrated Products 功能描述:DIGITAL THERM. 8P SO 208M TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC
DS1620S/T&R 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1620S+ 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1620S+T&R 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 3-WIRE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Digital Thermometer & Thermostat