- 您現在的位置：買賣IC網 > PDF目錄97860 > DS1511W (DALLAS SEMICONDUCTOR) 1 TIMER(S), REAL TIME CLOCK, DMA28 PDF資料下載
參數資料
| 型號： | DS1511W |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Timer or RTC |
| 英文描述： | 1 TIMER(S), REAL TIME CLOCK, DMA28 |
| 封裝： | MODULE, DIP-28 |
| 文件頁數： | 8/30頁 |
| 文件大?。?/td> | 291K |
| 代理商： | DS1511W |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
DS1501/DS1511
16 of 30
SQUARE WAVE OUTPUT
The square wave output is enabled and disabled via the E32K bit. If the square wave is enabled
( E32K ="0") and the oscillator is running, then a 32.768 kHz square wave will be output on the SQW pin.
If the Battery Backup 32 kHz enable bit (BB32) is enabled, and voltage is applied to VBAUX, then the
32.768 kHz square wave will be output on the SQW pin in the absence of VCC.
BATTERY MONITOR
The DS1501/DS1511 constantly monitors the battery voltage of the back-up battery sources (VBAT and
VBAUX). The Battery Low Flags BLF1 and BLF2 will be set to a "1" if the battery voltage on VBAT and
VBAUX are less than 2.5 volts (typical), otherwise BLF1 and BLF2 will be a "0". BLF1 monitors VBAT,
and BLF2 monitors VBAUX.
POWER-UP DEFAULT STATES
These bits are set upon power-up: EOSC ="0", E32K ="0", TIE="0", KIE="0", WDE="0", and WDS="0".
256 X 8 EXTENDED RAM
The DS1501/DS1511 provides 256 x 8 of on-chip SRAM which is controlled as nonvolatile storage
sustained from a lithium battery. On power-up, the RAM is taken out of write protect status by an internal
signal.
Access to the SRAM is controlled by two on-chip latch registers. One register is used to hold the SRAM
address, and the other is used to hold read/write data. The SRAM address space is from 00h to FFh. The
8-bit address of the RAM location to be accessed must be loaded into the extended RAM address register
located at 10h. Data in the addressed location may be read by performing a read operation from location
13h, or written to by performing a write operation to location 13h. Data in any addressed location may be
read or written repeatedly with changing the address in location 10h.
To read or write consecutive extended RAM locations, a burst mode feature can be enabled to increment
the extended RAM address. To enable the burst mode feature, set the BME bit to a 1. With burst mode
enabled, write the extended RAM starting address location to register 10h. Then read or write the
extended RAM data from/to register 13h. The extended RAM address locations are automatically
incremented on the rising edge of OE , WE , or CS only when register 13h is being accessed. Refer to the
Burst Mode Timing Waveform (Figure 7).
相關PDF資料 |
PDF描述 |
|---|---|
| DS1511Y | 1 TIMER(S), REAL TIME CLOCK, DMA28 |
| DS1501YE | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| DS1501WS | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| DS1501Y | 1 TIMER(S), REAL TIME CLOCK, PDIP28 |
| DS1501W | 1 TIMER(S), REAL TIME CLOCK, PDIP28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1511W+ | 功能描述:實時時鐘 Y2K-Compliant Watchdog RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1511Y | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1511Y+ | 功能描述:實時時鐘 Y2K-Compliant Watchdog RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1514FR000 | 制造商:Thomas & Betts 功能描述:100A,REC,4P5W,MG,514,3PY600V,SC |
| DS1514MP000 | 制造商:Thomas & Betts 功能描述:100A,PLG,4P5W,MG,514,3PY347V.SC |
發布緊急采購，3分鐘左右您將得到回復。