參數資料
型號： DS1501YN
英文描述： Y2K-Compliant Watchdog Real-Time Clocks
中文描述： 千年蟲的看門狗實時時鐘
文件頁數： 9/20頁
文件大?。?/td> 265K
代理商： DS1501YN
DS1501/DS1511 Y2KC Watchdog Real-Time Clocks
9 of 20
PIN DESCRIPTION
PIN
DIP, SO
MODULE
TSOP
NAME
FUNCTION
1
1
8
PWR
Active-Low Power-On Output (Open Drain). This output, if used, is normally
connected to power-supply control circuitry. This pin requires a pullup resistor
connected to a positive supply to operate correctly.
Connections for Standard 32.768kHz Quartz Crystal. For greatest accuracy, the
DS1501 must be used with a crystal that has a specified load capacitance of either
6pF or 12.5pF. The crystal select (CS) bit in control register B is used to select
operation with a 6pF or 12.5pF crystal. The crystal is attached directly to the X1 and
X2 pins. There is no need for external capacitors or resistors. An external 32.768kHz
oscillator can also drive the DS1501. In this configuration, the X1 pin is connected to
the external oscillator signal and the X2 pin is floated. For more information about
crystal selection and crystal layout considerations, refer to
Application Note 5
8:
Crystal Considerations with Dallas Real-Time Clocks
. See Figure 9. An enable bit in
the month register controls the oscillator. Oscillator startup time is highly dependent
upon crystal characteristics, PC board leakage, and layout. High ESR and excessive
capacitive loads are the major contributors to long startup times. A circuit using a
crystal with the recommended characteristics and proper layout usually starts within
one second.
Active-Low Reset Output. (Open Drain). This output, if used, is normally connected
to a microprocessor-reset input. This pin requires a pull up resistor connected to a
positive supply to operate correctly. When
RST
is active, the device is not accessible.
Active-Low Interrupt Output (Open Drain). This output, if used, is normally connected
to a microprocessor interrupt input. This pin requires a pullup resistor connected to a
positive supply to operate correctly.
Address Inputs. Selects one of 17 register locations.
2, 3
—
9, 10
X1, X2
4
4
11
RST
5
5
12
IRQ
6–10
11–13,
15–19
6–10
11–13,
15–19
13–17
18–20,
22–26
A4–A0
DQ0–DQ7
Data Input/Output. I/O pins for 8-bit parallel data transfer.
14, 21
14
21, 28
GND
Ground. DC power is applied to the device on these pins. V
CC
is the positive terminal.
When power is applied within the normal limits, the device is fully accessible and
data can be written and read. When V
CC
drops below the normal limits, reads and
writes are inhibited. As V
CC
drops below the battery voltage, the RAM and
timekeeping circuits are switched over to the battery.
Output-Enable Input. Active-low input that enables DQ0–DQ7 for data output from
the device.
22
22
1
OE
20
20
27
CE
Chip-Enable Input. Active-low input to enable the device.
23
23
2
SQW
Square-Wave Output. When enabled, the SQW pin outputs a 32.768kHz square
wave. If the square wave (
E32K
) and battery backup 32kHz (BB32) bits are enabled,
power is provided by V
BAUX
when V
CC
is absent.
Active-Low Kickstart Input. This pin is used to wake up a system from an external
event, such as a key closure. The
KS
pin is normally connected using a pullup
resistor to V
BAUX
. If the
KS
function is not used, connect to ground.
Battery Input for Any Standard 3V Lithium Cell or Other Energy Source. Battery
voltage must be held between 2.5V and 3.7V for proper operation. UL recognized to
ensure against reverse charging current when used with a lithium battery. If not
used, connect to ground.*
Auxiliary Battery Input for Any Standard 3V Lithium Cell or Other Energy Source.
Battery voltage must be held between 2.5V and 3.7V for proper operation. UL
recognized to ensure against reverse charging current when used with a lithium
battery. If not used, connect to ground.*
Write-Enable Input. Active-low input that enables DQ0–DQ7 for data input to the
device.
DC Power. V
CC
is the positive terminal. When power is applied within the normal
limits, the device is fully accessible and data can be written and read. When V
CC
drops below the normal limits, reads and writes are inhibited. As V
CC
drops below the
battery voltage, the RAM and timekeeping circuits are switched over to the battery.
24
24
3
KS
25
—
4
V
BAT
26
26
5
V
BAUX
27
27
6
WE
28
28
7
V
CC
—
2, 3, 21,
25
—
N.C.
No Connect
*
www.maxim-ic.com/TechSupport/QA/ntrl.htm
相關PDF資料
PDF描述
DS1511W Y2K-Compliant Watchdog Real-Time Clocks
DS1511Y Y2K-Compliant Watchdog Real-Time Clocks
DS1501WSN Y2K-Compliant Watchdog Real-Time Clocks
DS1611S Power Supply Supervisor
DS1611SN Power Supply Supervisor
相關代理商/技術參數
參數描述
DS1501YN+ 功能描述:實時時鐘 Y2K-Compliant Watchdog RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS1501YS 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS1501YS+ 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS1501YS+T&R 制造商:Maxim Integrated Products 功能描述:IC RTC WDOG Y2K 5V 28-SOIC
DS1501YS+T&R 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。