參數資料
型號: DS1318
元件分類: 通用總線功能
英文描述: Parallel-Interface Elapsed Time Counter
中文描述: 并行接口歷時計數器
文件頁數: 13/14頁
文件大?。?/td> 158K
代理商: DS1318
Bit 7: Oscillator Stop Flag (OSF).
A logic 1 in this bit
indicates that the oscillator either is or was stopped for
some period of time and may be used to judge the
validity of the timekeeping data. This bit is set to logic 1
any time the oscillator stops. The following are exam-
ples of conditions that can cause the OSF bit to be set:
1)
The first time power is applied.
2)
The voltage present on both V
CC
and V
BAT
is
insufficient to support oscillation.
3)
The ENOSC bit is turned off in battery-backed
mode.
4)
External influences on the crystal (i.e., noise, leak-
age, etc.)
Any write to the status register while this flag is active
clears the bit to 0.
Bit 6: Update-In-Progress Flag (UIP).
A logic 1 in the
update-in-progress bit indicates that the internal clock
registers may be in the process of updating the user
registers. Writing to any seconds or subseconds regis-
ters when this bit is logic 1 may cause a collision with
the internal update and corrupt one or more of the user
registers until the next update occurs. If the UIP bit is
read and is logic 0, the user has at least 60μs to write
to the device without the possibility of causing a colli-
sion with the internal update. The internal timekeeping
update is gated by the falling edge of UIP.
Reading the subseconds and or seconds registers
while UIP is logic 1 may result in reading inconstant val-
ues. If the UIP bit is read and is logic 0, the user has at
least 60μs to read from the device without the possibili-
ty of getting inconstant values.
Bit 1: Periodic Flag (PF).
The periodic flag bit is set to
1 at the rate determined by the PRS bits in register 0Bh.
If the PF bit is already 1 when the selected frequency
attempts to set it to 1 again, no change occurs. The
user must clear the PIF flag faster than the part
attempts to set it to see the desired PF rate. If the PIE
bit in register 0Ah is also set to logic 1, the
IRQ
pin is
driven low in response to PF transitioning to 1. Any
write to the status register while this flag is active clears
the bit to 0.
Bit 0: Alarm Flag (ALMF).
A logic 1 in the alarm flag
bit indicates that the contents of the seconds registers
matched the contents of the alarm registers. If the AIE
bit in register 0Ah is also set to logic 1, the
IRQ
pin is
driven low in response to ALMF transitioning to 1. Any
write to the status register while this flag is active clears
the bit to 0.
D
Parallel-Interface Elapsed Time Counter
____________________________________________________________________
13
BIT 7
OSF
BIT 6
UIP
BIT 5
0
BIT 4
0
BIT 3
0
BIT 2
0
BIT 1
PF
BIT 0
ALMF
Status Register (0Ch)
60
μ
s
8kHz
4kHz
UIP
UIP vs. Update Timing
相關PDF資料
PDF描述
DS1321 Flexible Nonvolatile Controller with Lithium Battery Monitor
DS1330AB 256k Nonvolatile SRAM with Battery Monitor
DS1330YP-100-IND Isolation Transformer
DS1330ABP-100 256k Nonvolatile SRAM with Battery Monitor
DS1330ABP-100-IND 256k Nonvolatile SRAM with Battery Monitor
相關代理商/技術參數
參數描述
DS1318_10 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Parallel-Interface Elapsed Time Counter
DS1318E 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Parallel-Interface Elapsed Time Counter
DS1318E/GG8 制造商:Maxim Integrated Products 功能描述:44 BIT PARALLEL INTFACE ETC 24P TSS - Rail/Tube
DS1318E+ 功能描述:實時時鐘 Parallel-Interface Elapsed Time Cntr RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS1318E+T&R 制造商:Maxim Integrated Products 功能描述:44 BIT PRLLEL INTFC ETC TRL LF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC COUNTER ELAPSED TIME 24TSSOP