- 您現在的位置：買賣IC網 > PDF目錄376950 > DS1305 Serial Alarm Real Time Clock RTC PDF資料下載
參數資料
| 型號： | DS1305 |
| 英文描述： | Serial Alarm Real Time Clock RTC |
| 中文描述： | 帶有鬧鐘的串行實時時鐘 |
| 文件頁數： | 7/22頁 |
| 文件大?。?/td> | 257K |
| 代理商： | DS1305 |
DS1305
7 of 22
TIME OF DAY ALARM MASK BITS Table 1
ALARM REGISTER MASK BITS (BIT 7)
SECONDS
MINUTES
1
1
0
1
0
0
0
0
0
0
HOURS
1
1
1
0
0
DAYS
1
1
1
1
0
Alarm once per second
Alarm when seconds match
Alarm when minutes and seconds match
Alarm hours, minutes and seconds match
Alarm day, hours, minutes and seconds match
SPECIAL PURPOSE REGISTERS
The DS1305 has three additional registers (Control Register, Status Register and Trickle Charger
Register) that control the real time clock, interrupts and trickle charger.
CONTROL REGISTER (READ 0FH, WRITE 8FH)
BIT7
BIT6
BIT5
BIT4
BIT3
BIT2
BIT1
BIT0
EOSC
WP
0
0
0
INTCN
AIE1
AIE0
EOSC
(Enable oscillator)
- This bit when set to logic 0 will start the oscillator. When this bit is set to a
logic 1, the oscillator is stopped and the DS1305 is placed into a low-power standby mode with a current
drain of less than 100 nanoamps when power is supplied by V
BAT
or V
CC2
. The initial power on state is
not defined.
WP (Write Protect)
- Before any write operation to the clock or RAM, this bit must be logic 0. When
high, the write protect bit prevents a write operation to any register, including bits 0, 1, 2 and 7 of the
control register. Upon initial power up, the state of the WP bit is undefined. Therefore the WP bit should
be cleared before attempting to write to the device.
INTCN (Interrupt Control)
- This bit controls the relationship between the two time of day alarms and
the interrupt output pins. When the INTCN bit is set to a logic 1, a match between the timekeeping
registers and the Alarm 0 registers will activate the
INT0
pin (provided that the alarm is enabled) and a
match between the timekeeping registers and the Alarm 1 registers will activate the
INT1
pin (provided
that the alarm is enabled). When the INTCN bit is set to a logic 0, a match between the timekeeping
registers and either Alarm 0 or Alarm 1 will activate the
INT0
pin (provided that the alarms are enabled).
INT1
has no function when INTCN is set to a logic 0.
AIE0 (Alarm Interrupt Enable 0)
- When set to a logic 1, this bit permits the Interrupt 0 Request Flag
(IRQF0) bit in the status register to assert
INT0
.
When the AIE0 bit is set to logic 0, the IRQF0 bit does
not initiate the
INT0
signal.
AIE1 (Alarm Interrupt Enable 1)
- When set to a logic 1, this bit permits the Interrupt 1 Request Flag
(IRQF1) bit in the status register to assert
INT1
(when INTCN=1) or to assert
INT0
(when INTCN=0).
When the AIE1 bit is set to logic 0, the IRQF1 bit does not initiate an interrupt signal.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1305E | Serial Alarm Real Time Clock RTC |
| DS1305N | Serial Alarm Real Time Clock RTC |
| DS1306EN | Serial Alarm Real Time Clock RTC |
| DS1306 | Serial Alarm Real Time Clock RTC |
| DS1306E | Serial Alarm Real Time Clock RTC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1305_05 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Serial Alarm Real-Time Clock |
| DS1305+ | 功能描述:實時時鐘 Serial Alarm RTC 3-Wire RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1305E | 功能描述:實時時鐘 Serial Alarm RTC 3-Wire RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1305E/R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Serial Alarm Real-Time Clock |
| DS1305E/T | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Serial Alarm Real-Time Clock |
發布緊急采購，3分鐘左右您將得到回復。