參數資料
型號: DS1250Y-70
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: Static RAM
英文描述: 512K X 8 NON-VOLATILE SRAM MODULE, 70 ns, DMA32
封裝: 0.740 INCH, DIP-32
文件頁數: 10/12頁
文件大?。?/td> 294K
代理商: DS1250Y-70
DS1250Y/AB
7 of 12
POWER-DOWN/POWER-UP TIMING
(tA: See Note 10)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
NOTES
VCC Fail Detect to CE and WE Inactive
tPD
1.5
μs
11
VCC slew from VTP to 0V
tF
150
μs
VCC slew from 0V to VTP
tR
150
μs
VCC Valid to CE and WE Inactive
tPU
2
ms
VCC Valid to End of Write Protection
tREC
125
ms
(tA=25°C)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
NOTES
Expected Data Retention Time
tDR
10
years
9
WARNING:
Under no circumstance are negative undershoots, of any amplitude, allowed when device is in battery
backup mode.
NOTES:
1. WE is high for a Read Cycle.
2. OE = VIH or VIL. If OE = VIH during write cycle, the output buffers remain in a high-impedance state.
3. tWP is specified as the logical AND of CE and WE . tWP is measured from the latter of CE or WE
going low to the earlier of CE or WE going high.
4. tDH, tDS are measured from the earlier of CE or WE going high.
5. These parameters are sampled with a 5 pF load and are not 100% tested.
6. If the CE low transition occurs simultaneously with or latter than the WE low transition, the output
buffers remain in a high-impedance state during this period.
7. If the CE high transition occurs prior to or simultaneously with the WE high transition, the output
buffers remain in high-impedance state during this period.
8. If WE is low or the WE low transition occurs prior to or simultaneously with the CE low transition,
the output buffers remain in a high-impedance state during this period.
9. Each DS1250 has a built-in switch that disconnects the lithium source until the user first applies VCC.
The expected tDR is defined as accumulative time in the absence of VCC starting from the time power
is first applied by the user. This parameter is assured by component selection, process control, and
design. It is not measured directly during production testing.
10. All AC and DC electrical characteristics are valid over the full operating temperature range. For
commercial products, this range is 0
°C to 70°C. For industrial products (IND), this range is -40°C to
+85
°C.
11. In a power-down condition the voltage on any pin may not exceed the voltage on VCC.
12. tWR1 and tDH1 are measured from WE going high.
13. tWR2 and tDH2 are measured from CE going high.
14. DS1250 modules are recognized by Underwriters Laboratory (U.L.
) under file E99151.
相關PDF資料
PDF描述
DS1250YP-100 512K X 8 NON-VOLATILE SRAM MODULE, 100 ns, DMA34
DS1250YP-70 512K X 8 NON-VOLATILE SRAM MODULE, 70 ns, DMA34
DS1250ABP-100 512K X 8 NON-VOLATILE SRAM MODULE, 100 ns, DMA34
DS1250AB-70 512K X 8 NON-VOLATILE SRAM MODULE, 70 ns, DMA32
DS1250YL-70-IND 512K X 8 NON-VOLATILE SRAM MODULE, 70 ns, DMA34
相關代理商/技術參數
參數描述
DS1250Y-70+ 功能描述:NVRAM 4096K NV SRAM RoHS:否 制造商:Maxim Integrated 數據總線寬度:8 bit 存儲容量:1024 Kbit 組織:128 K x 8 接口類型:Parallel 訪問時間:70 ns 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 工作電流:85 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 封裝 / 箱體:EDIP 封裝:Tube
DS1250Y-70IND 功能描述:NVRAM RoHS:否 制造商:Maxim Integrated 數據總線寬度:8 bit 存儲容量:1024 Kbit 組織:128 K x 8 接口類型:Parallel 訪問時間:70 ns 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 工作電流:85 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 封裝 / 箱體:EDIP 封裝:Tube
DS1250Y-70-IND 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NVRAM (Battery Based)
DS1250Y-70IND+ 功能描述:NVRAM 4096K NV SRAM RoHS:否 制造商:Maxim Integrated 數據總線寬度:8 bit 存儲容量:1024 Kbit 組織:128 K x 8 接口類型:Parallel 訪問時間:70 ns 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 工作電流:85 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 封裝 / 箱體:EDIP 封裝:Tube
DS1250Y-70-W 功能描述:NVRAM RoHS:否 制造商:Maxim Integrated 數據總線寬度:8 bit 存儲容量:1024 Kbit 組織:128 K x 8 接口類型:Parallel 訪問時間:70 ns 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 工作電流:85 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 封裝 / 箱體:EDIP 封裝:Tube