- 您現在的位置：買賣IC網 > PDF目錄97858 > DS1230WP-150 (DALLAS SEMICONDUCTOR) 32K X 8 NON-VOLATILE SRAM MODULE, 150 ns, DMA34 PDF資料下載
參數資料
| 型號： | DS1230WP-150 |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Static RAM |
| 英文描述： | 32K X 8 NON-VOLATILE SRAM MODULE, 150 ns, DMA34 |
| 封裝： | POWERCAP MODULE-34 |
| 文件頁數： | 4/11頁 |
| 文件大小： | 217K |
| 代理商： | DS1230WP-150 |
DS1230W
2 of 11
DESCRIPTION
The DS1230W 3.3V 256k Nonvolatile SRAM is a 262,144-bit, fully static, nonvolatile SRAM organized
as 32,768 words by 8 bits. Each NV SRAM has a self-contained lithium energy source and control
circuitry which constantly monitors VCC for an out-of-tolerance condition. When such a condition occurs,
the lithium energy source is automatically switched on and write protection is unconditionally enabled to
prevent data corruption. DIP-package DS1230W devices can be used in place of existing 32k x 8 static
RAMs directly conforming to the popular bytewide 28-pin DIP standard. The DIP devices also match the
pinout of 28256 EEPROMs, allowing direct substitution while enhancing performance. DS1230W
devices in the PowerCap Module package are directly surface mountable and are normally paired with a
DS9034PC PowerCap to form a complete Nonvolatile SRAM Module. There is no limit on the number of
write cycles that can be executed and no additional support circuitry is required for microprocessor
interfacing.
READ MODE
The DS1230W executes a read cycle whenever WE (Write Enable) is inactive (high) and CE (Chip
Enable) and OE (Output Enable) are active (low). The unique address specified by the 15 address inputs
(A0 – A14) defines which of the 32,768 bytes of data is to be accessed. Valid data will be available to the
eight data output drivers within tACC (Access Time) after the last address input signal is stable, providing
that CE and OE (Output Enable) access times are also satisfied. If OE and CE access times are not
satisfied, then data access must be measured from the later-occurring signal ( CE or OE ) and the limiting
parameter is either tCO for CE or tOE for OE rather than address access.
WRITE MODE
The DS1230W executes a write cycle whenever the WE and CE signals are active (low) after address
inputs are stable. The later-occurring falling edge of CE or WE will determine the start of the write cycle.
The write cycle is terminated by the earlier rising edge of CE or WE . All address inputs must be kept
valid throughout the write cycle. WE must return to the high state for a minimum recovery time (tWR)
before another cycle can be initiated. The OE control signal should be kept inactive (high) during write
cycles to avoid bus contention. However, if the output drivers are enabled ( CE and OE active) then WE
will disable the outputs in tODW from its falling edge.
DATA RETENTION MODE
The DS1230W provides full functional capability for VCC greater than 3.0 volts and write protects by 2.8
volts. Data is maintained in the absence of VCC without any additional support circuitry. The nonvolatile
static RAMs constantly monitor VCC. Should the supply voltage decay, the NV SRAMs automatically
write protect themselves, all inputs become “don’t care,” and all outputs become high-impedance. As VCC
falls below approximately 2.5 volts, a power switching circuit connects the lithium energy source to
RAM to retain data. During power-up, when VCC rises above approximately 2.5 volts, the power
switching circuit connects external VCC to RAM and disconnects the lithium energy source. Normal
RAM operation can resume after VCC exceeds 3.0 volts.
FRESHNESS SEAL
Each DS1230W device is shipped from Dallas Semiconductor with its lithium energy source
disconnected, guaranteeing full energy capacity. When VCC is first applied at a level greater than 3.0
volts, the lithium energy source is enabled for battery back-up operation.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1230YL-70 | 32K X 8 NON-VOLATILE SRAM MODULE, 70 ns, DMA34 |
| DS1243Y-120 | 0 TIMER(S), REAL TIME CLOCK, PDIP28 |
| DS1243Y-150 | 0 TIMER(S), REAL TIME CLOCK, PDIP28 |
| DS1243Y | 0 TIMER(S), REAL TIME CLOCK, PDIP28 |
| DS1244W-120 | 0 TIMER(S), REAL TIME CLOCK, PDIP28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1230WP-150+ | 功能描述:NVRAM 3.3V 256k Nonvolatile SRAM RoHS:否 制造商:Maxim Integrated 數據總線寬度:8 bit 存儲容量:1024 Kbit 組織:128 K x 8 接口類型:Parallel 訪問時間:70 ns 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 工作電流:85 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 封裝 / 箱體:EDIP 封裝:Tube |
| DS1230WP-150-IND | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3.3V 256k Nonvolatile SRAM |
| DS1230Y | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:256k Nonvolatile SRAM |
| DS1230Y/AB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:256K Nonvolatile SRAM |
| DS1230Y_10 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:256k Nonvolatile SRAM |
發布緊急采購，3分鐘左右您將得到回復。