- 您現在的位置：買賣IC網 > PDF目錄1993 > DS1123LE-100+ (Maxim Integrated Products)IC DELAY LINE 256TAP 16-TSSOP PDF資料下載
參數資料
| 型號： | DS1123LE-100+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DELAY LINE 256TAP 16-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 96 |
| 標片/步級數： | 256 |
| 功能： | 單發射，可編程 |
| 延遲到第一抽頭： | 16.5ns |
| 接頭增量： | 1ns |
| 可用的總延遲： | 255ns |
| 獨立延遲數： | 1 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
DS1123L
3.3V, 8-Bit, Programmable Timing Element
10
_____________________________________________________________________
To read the current values stored by the 3-wire
device(s), the latch must be enabled and the value of Q
must be read and then written back to D before the
register is clocked. This causes the current value of the
register to be written back into the DS1123L as it is
being read. This can be accomplished in a couple of
different ways. If the microprocessor has an I/O pin that
is high impedance when set as an input, a feedback
resistor (generally between 1k
Ω and 10kΩ) can be
used to write the data on Q back to D as the value is
read (see Figure 5a). If the microprocessor has an
internal pullup on its I/O pins, or only offers separate
input and output pins, the value in the register can still
be read. The circuit shown in Figure 5b allows the Q
values to read by the microprocessor, which must write
the Q value to D before it can clock the bus to read the
next bit. If the Q values are read without writing them to
D (with the pullup or otherwise), the read is destructive.
A destructive read cycle likely results in an undesirable
change in the delay setting.
Figure 5c shows how to cascade multiple DS1123L’s
onto the same 3-wire bus. One important detail of writ-
ing software for cascaded 3-wire devices is that all the
devices on the bus must be written to or read from dur-
ing each read or write cycle. Attempting to write to only
the first device (U1) would cause the data stored in U1
MICROPROCESSOR
OUTPUT
I/O PIN
LE
CLK
DQ
RFB
MICROPROCESSOR
OUTPUT
INPUT
A) USING A FEEDBACK RESISTOR WITH AN I/O PIN FOR READING
THE DS1123L
B) USING A SEPARATE INPUT PIN TO READ THE DS1123L
MICROPROCESSOR
LE
CLK
DQ
LE
CLK
DQ
LE
CLK
DQ
OUTPUT
I/O PIN
RFB
C) CASCADING MULTIPLE DS1123L'S ON A 3-WIRE BUS
VCC
LE
CLK
DQ
P/S
DS1123L
U1
U2
U3
DS1123L
Figure 5. Using the Serial Interface
相關PDF資料 |
PDF描述 |
|---|---|
| DS1124U-25+T | IC DELAY LINE 256TAP 10-USOP |
| DS1135LU-300/T&R | IC DELAY LINE 300NS 8-USOP |
| DS1135Z-12/T&R | IC DELAY LINE 12NS 8-SOIC |
| DS1181LE+ | IC CLOCK MOD SS 8-TSSOP |
| DS1243Y-120 | IC NVSRAM 64KBIT 120NS 28DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1123LE-100+ | 功能描述:延遲線/計時元素 Programmable 3.3V 8 Bit Timing Element RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube |
| DS1123LE-200 | 功能描述:延遲線/計時元素 Programmable 3.3V 8 Bit Timing Element RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube |
| DS1123LE-200+ | 功能描述:延遲線/計時元素 Programmable 3.3V 8 Bit Timing Element RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube |
| DS1123LE-25 | 功能描述:延遲線/計時元素 Programmable 3.3V 8 Bit Timing Element RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube |
| DS1123LE-25+ | 功能描述:延遲線/計時元素 Programmable 3.3V 8 Bit Timing Element RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。