參數資料
型號： DRM057
英文描述： Open Loop Universal Motor Chopper based on the MC68HC908QT4 Microcontroller
中文描述： 開環通用汽車在MC68HC908QT4斬波基于單片機
文件頁數： 44/48頁
文件大小： 1131K
代理商： DRM057
Receiver Firmware
Designer Reference Manual
DRM050 — Rev 0
44
Receiver Firmware
MOTOROLA
8.3 Remote Wakeup
The JB16 receiver supports remote wakeup function that can wake up
the host computer during USB suspend.
During suspend, the MCU will be periodically woken up by the IRQ
driven by the external RC charging and discharging circuit. The MCU
then turns on the RF circuit (both RFW-D100 and RFW-D102) for a short
period of time, detect whether a valid mouse or keyboard RF packet
arrived for waking up the host. During this short period, the IRQ will serve
for RFW-D100 interrupt events again.
If no valid packet has been detected in this period, the receiver will sleep
again. The MCU will initiate the charging and discharging cycle again
before it enters power saving mode.
The mouse or keyboard can re-transmit an RF packet again if there is no
acknowledgment from the JB16 receiver. The maximum number of such
re-transmissions can be adjusted through the MAC application interface
transmission function.
For the JB16 receiver to be able to detect the incoming packet, some
timing parameters needed to be considered.
The first is the small wakeup duration at each IRQ wakeup. For example,
if the receiver is sleeping while a packet arrives, the transmitter will send
out a second packet because there is no acknowledge from the receiver.
If the IRQ wakeup period longer than the interval between the first and
next re-transmitted packet, the re-transmitted packet can be detected by
the receiver.
Another timing is the interval between two IRQ interrupts. Consider a
single key has been pressed on the keyboard. If an IRQ wakeup
detection duty in the receiver has just elapsed before the arrival of the
first RF keyboard packet, the receiver cannot detect that packet. The
next wakeup duty will start at the next IRQ interrupt.
It can be seen that for a smaller number of re-transmission setting in the
keyboard, all re-transmission may have taken place before the next
wakeup duty start. This means the receiver will fail to detect the pressed
key and cannot wake up the host. Therefore, the interval between two
IRQ interrupts should be shorter for a relative small re-transmission
setting in the transmitter. This time interval can be adjusted by the
external RC values, C22, and R45.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
DRM058 MC68HC908QY4 LIN Backlit Keypad Slave Designer Reference Manual
DRM059 Cluster for Motorbikes Using the MC68HC908LJ12 and MC33970
DRM061 USB Thumb Drive
DRM064 Single Phase On-Line UPS Using MC9S12E128
DRP3510 Digital Receiver Front-end
相關代理商/技術參數
參數描述
DRM10 功能描述:DIP 開關/ SIP 開關 BCD 10 POS RoHS:否 制造商:Omron Electronics 位置數量:10 開關類型:DIP 執行器:Rotary 端子節距:2.54 mm 觸點形式: 端接類型:Solder Pin 電流額定值:100 mA 電壓額定值 DC: 工作溫度范圍: 安裝:Through Hole
DRM1004 功能描述:DIP 開關/ SIP 開關 ROTARY DIP SWITCH PLASTICSHAFT RoHS:否 制造商:Omron Electronics 位置數量:10 開關類型:DIP 執行器:Rotary 端子節距:2.54 mm 觸點形式: 端接類型:Solder Pin 電流額定值:100 mA 電壓額定值 DC: 工作溫度范圍: 安裝:Through Hole
DRM101 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Blood Pressure Monitor Using the Flexis QE128 Family
DRM10C 功能描述:SWITCH DIP MINI SHAFT 10POS T/H RoHS:否 類別:開關 >> DIP 系列:DR 特色產品:RDM Series Rotary DIP Switch 標準包裝:70 系列:RDM 電路:十六進制 位置數:16 觸點額定電壓:0.1A @ 42VDC 觸動器類型:用于工具旋轉 觸動器電平:凹槽式 安裝類型:通孔 方向:頂部觸動 可清洗:是 其它名稱:EG4977-5RDMAR16PIT
DRM10C04 功能描述:編碼式波段開關 SW DIP MINI SHAFT 10POS T/H RoHS:否 制造商:C&K Components 位置數量:10 輸出代碼:Binary Coded Decimal 執行器:Screwdriver 觸點額定值: 端接類型:Solder Pin 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*