- 您現在的位置：買賣IC網 > PDF目錄376822 > DN8899UAS (PANASONIC CORP) Hall IC for alternative magnetic field SOH-4D type PDF資料下載
參數資料
| 型號： | DN8899UAS |
| 廠商： | PANASONIC CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Hall IC for alternative magnetic field SOH-4D type |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO4 |
| 封裝： | 0.200 INCH, PLASTIC, SOP-4 |
| 文件頁數： | 5/6頁 |
| 文件大?。?/td> | 45K |
| 代理商： | DN8899UAS |
Hall ICs
DN8899UAS
5
I
Caution on use of Hall ICs
As the Hall IC is often used to detect movement, the position of a Hall IC may be changed, and there is the risk of
a change in detection level, if exposed to shock or vibration over a long period of time. Secure the IC by applying
adhesive to the package or placing in a dedicated case.
1. On mounting of the surface mount type (ESO004-P-0200 package)
Set pin 2 to open or connect to GND. It will be damaged if it is connected to V
CC
. When mounted on the printed
circuit board, the Hall IC may be highly stressed by the warp that may occur from the soldering. This may also cause
a change in the operating magnetic flux density and a deterioration of its resistance to moisture.
Be cautious to keep the device from being stressed thermally or mechanically up to the 2 mm distance from the
package.
2. On using flux in soldering
Choose a flux which does not include ingredients from halogen group, such as chlorine, fluorine, etc. The
ingredients of halogen group may enter where the lead frame and package resin joint, causing corrosion and the
disconnection of the aluminum wiring on the surface of an IC chip.
3. On fixing a Hall IC with the holder
When a Hall IC is mounted on the printed circuit board with a holder and the coefficient of expansion of the holder
is large, the lead wire of the Hall IC will be stretched and it may give a stress to the Hall IC.
If the lead wire is stressed intensely due to the distortion of holder or board, the adhesives between the package
and the lead wire may be weakened and cause a minute gap resulting in the deterioration of its resistance to moisture.
Sensitivity may also be changed by this stress.
4. Power supply line/power transmission line
If a power supply line/power transmission line becomes longer, noise and/or oscillation may be found on the line.
In this case, set the capacitor of 0.1
μ
F to 10
μ
F near a Hall IC to prevent it.
If a voltage of 18 V or more is thought to be applied to the power supply line (flyback voltage from coil or the
ignition pulse, etc.), avoid it with external components (capacitor, resistor, Zener diode, diode, surge absorbing ele-
ments, etc.).
5. V
CC
and GND
Do not reverse V
CC
and GND. If the V
CC
and GND pins are reversely connected, this IC will be destroyed. If the
IC GND-pin voltage is set higher than other pin voltage, the IC configuration will become same as a forward biased
diode. Therefore, it will turn on at the diode forward voltage (approximately 0.7 V), and a large current will flow
through the IC, ending up in its destruction. (This is common to Monolithic IC.)
6. Cautions on power ON of Hall IC
When a Hall IC is turned ON, the position of the magnet or looseness may change the output of a Hall IC, and a
pulse may be generated. Therefore, care should be given whenever the output state of a Hall IC is critical when the
supply power is ON.
7. When magnetic force of magnet is too strong
Output may be inverted when applying a magnetic flux density of 100mT or more. Accordingly, magnetic flux
density should be used within the range of 100 mT.
相關PDF資料 |
PDF描述 |
|---|---|
| DN8899TE | Hall IC (Operating Temperature Range Topr=-40 to +100∑C, Operating in Alternative Magnetic Field) |
| DN8899 | Hall IC (Operating Temperature Range Topr=-40 to +100∑C, Operating in Alternative Magnetic Field) |
| DN8899S | Hall IC (Operating Temperature Range Topr=-40 to +100∑C, Operating in Alternative Magnetic Field) |
| DN8899SE | Hall IC (Operating Temperature Range Topr=-40 to +100∑C, Operating in Alternative Magnetic Field) |
| DNC3X3125 | 10/100 Mbits/s Ethernet Transceiver Macrocell(10M位/秒和100 M位/秒以太網收發(fā)器宏單元) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DN8S03TTE | 功能描述:TVS 二極管 - 瞬態(tài)電壓抑制器 DIODE TERMINATION NETWORK RoHS:否 制造商:Vishay Semiconductors 極性:Bidirectional 工作電壓: 擊穿電壓:58.9 V 鉗位電壓:77.4 V 峰值浪涌電流:38.8 A 系列: 封裝 / 箱體:DO-214AB 最小工作溫度:- 55 C 最大工作溫度:+ 150 C |
| DN-900G | 功能描述:網絡模塊 900MHz RS-232C Serial Modem RoHS:否 制造商:Digi International 產品:ZigBee to Ethernets 處理器類型: 頻率: 隨機存取存儲器: 閃光: 數據速率: 接口類型:Ethernet, RF 工作電源電壓:5 V 最大工作溫度:+ 40 C 尺寸:70 mm x 95 mm x 32 mm |
| DN-900GX | 功能描述:網絡模塊 NEMA 4X/IP66 900MHz RS-232 X Ant RoHS:否 制造商:Digi International 產品:ZigBee to Ethernets 處理器類型: 頻率: 隨機存取存儲器: 閃光: 數據速率: 接口類型:Ethernet, RF 工作電源電壓:5 V 最大工作溫度:+ 40 C 尺寸:70 mm x 95 mm x 32 mm |
| DN-900I | 功能描述:網絡模塊 NEMA 4X/IP66 900MHz RS-485 RoHS:否 制造商:Digi International 產品:ZigBee to Ethernets 處理器類型: 頻率: 隨機存取存儲器: 閃光: 數據速率: 接口類型:Ethernet, RF 工作電源電壓:5 V 最大工作溫度:+ 40 C 尺寸:70 mm x 95 mm x 32 mm |
| DN-900IX | 功能描述:網絡模塊 NEMA 4X/IP66 900MHz RS-485 X Ant RoHS:否 制造商:Digi International 產品:ZigBee to Ethernets 處理器類型: 頻率: 隨機存取存儲器: 閃光: 數據速率: 接口類型:Ethernet, RF 工作電源電壓:5 V 最大工作溫度:+ 40 C 尺寸:70 mm x 95 mm x 32 mm |
發(fā)布緊急采購，3分鐘左右您將得到回復。