參數資料
型號: DG445EGE
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 多路復用及模擬開關
英文描述: QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, PQCC16
封裝: 5 X 5 MM, 0.90 MM HEIGHT, QFN-16
文件頁數: 6/10頁
文件大?。?/td> 396K
代理商: DG445EGE
D
Improved, Quad, SPST Analog Switches
6
_______________________________________________________________________________________
t
OFF
0.8 x V
OUT
V
OUT
0.8 x V
OUT
tf < 20ns
tr < 20ns
50%
0V
0V
+3V
SWITCH
OUTPUT
LOGIC INPUT WAVEFORM IS INVERTED FOR SWITCHES
THAT HAVE THE OPPOSITE LOGIC SENSE.
t
ON
SWITCH
INPUT
LOGIC
INPUT
+3V
IN
+5V
V-
-15V
( )
R
L
C
L
V
OUT
S
C
L
INCLUDES FIXTURE AND STRAY CAPACITANCE.
GND
REPEAT TEST FOR CHANNELS 2, 3, AND 4.
V
OUT
= V
D
L
LOGIC
INPUT
V
L
+15V
V+
D
DG444
DG445
Figure 2. Switching Time
Applications Information
General Operation
Switches are open when power is off.
IN, D, and S should not exceed V+ or V-, even with
the power off.
Switch leakage is from each analog switch terminal
to V+ or V-, not to other switch terminals.
Operation with Supply Voltages
Other than ±15V
Using supply voltages other than ±15V will reduce the
analog signal range. The DG444/DG445 switches oper-
ate with ±4.5V to ±20V bipolar supplies or with a +10V
to +30V single supply; connect V- to 0V when operating
with a single supply. Also, all device types can operate
with unbalanced supplies such as +24V and -5V. V
L
must be connected to +5V to be TTL compatible, or to
V+ for CMOS-logic level inputs. The
Typical Operating
Characteristics
graphs show typical on-resistance with
±20V, ±15V, ±10V, and ±5V supplies. (Switching times
increase by a factor of two or more for operation at ±5V.)
Overvoltage Protection
Proper power-supply sequencing is recommended
for all CMOS devices. Do not exceed the absolute
maximum ratings because stresses beyond the list-
ed ratings may cause permanent damage to the
devices. Always sequence V+ on first, followed by
V
L
, V-, and logic inputs. If power-supply sequenc-
ing is not possible, add two small, external signal
diodes in series with supply pins for overvoltage
protection (Figure 1). Adding diodes reduces the
analog signal range to 1V below V+ and 1V above
V-, but low switch resistance and low leakage char-
acteristics are unaffected. Device operation is
unchanged, and the difference between V+ and V-
should not exceed +44V.
V+
D
V-
S
V
g
Figure 1. Overvoltage Protection Using External Blocking Diodes
_____________________Pin Description
13
12
5
4
3, 14, 11, 6
2, 15, 10, 7
1, 16, 9, 8
IN1–IN4
D1–D4
S1–S4
V-
GND
V
L
V+
Positive-Supply-
Voltage Input—
Connected to
Substrate
Logic-Supply
Voltage Input
Ground
Negative-Supply
Voltage Input
Source Outputs
Drain Outputs
Logic Control
Inputs
NAME
FUNCTION
11
10
3
2
1, 12, 9, 4
16, 13, 8, 5
15, 14, 7, 6
PIN
DIP/SO
QFN
相關PDF資料
PDF描述
DG506AC/D+ 16-CHANNEL, SGL ENDED MULTIPLEXER, UUC
DG723DN-T1-GE4 DUAL 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDSO8
DGD250881UT-555R 836.5 MHz(Tx), 881.5 MHz(Rx), DUPLEXER
DGP12US12 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
DH40141-M208D SILICON, PIN DIODE
相關代理商/技術參數
參數描述
DG445ETE+ 功能描述:模擬開關 IC Quad SPST CMOS Normally Open RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻(最大值):0.1 Ohms 切換電壓(最大): 開啟時間(最大值): 關閉時間(最大值): 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16
DG445ETE+T 功能描述:模擬開關 IC Quad SPST CMOS Normally Open RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻(最大值):0.1 Ohms 切換電壓(最大): 開啟時間(最大值): 關閉時間(最大值): 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16
DG447 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Low Power, High Voltage SPST Analog Switches
DG447_11 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Low Power, High Voltage SPST Analog Switches
DG447DV-T1-E3 功能描述:模擬開關 IC Lo-Pwr HV Dual SPST RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻(最大值):0.1 Ohms 切換電壓(最大): 開啟時間(最大值): 關閉時間(最大值): 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16