- 您現在的位置：買賣IC網 > PDF目錄17082 > DC935A (Linear Technology)BOARD DAC LTC2605 PDF資料下載
參數資料
| 型號： | DC935A |
| 廠商： | Linear Technology |
| 文件頁數： | 3/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DAC LTC2605 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC935A Design Files DC935A Schematic |
| 標準包裝： | 1 |
| 系列： | QuikEval™ |
| DAC 的數量： | 8 |
| 位數： | 16 |
| 數據接口： | I²C |
| 設置時間： | 10µs |
| DAC 型： | 電壓 |
| 工作溫度： | 0°C ~ 70°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | LTC2605 |
| 相關產品： | LTC2605IGN-1#TRPBF-ND - IC DAC 16BIT OCT I2C 16-SSOP LTC2605IGN#TRPBF-ND - IC DAC 16BIT OCT I2C 16-SSOP LTC2605CGN-1#TRPBF-ND - IC DAC 16BIT OCT I2C 16-SSOP LTC2605CGN#TRPBF-ND - IC DAC 16BIT OCT I2C 16-SSOP LTC2605CGN-1#PBF-ND - IC DAC 16BIT OCT I2C 16-SSOP LTC2605CGN#PBF-ND - IC DAC 16BIT OCT I2C 16-SSOP LTC2605IGN#PBF-ND - IC DAC 16BIT OCT I2C 16-SSOP LTC2605IGN-1#PBF-ND - IC DAC 16BIT OCT I2C 16-SSOP |
LTC2605/LTC2615/LTC2625
11
2605fa
OPERATION
Power-On Reset
The LTC2605/LTC2615/LTC2625 clear the outputs to
zero-scale when power is rst applied, making system
initialization consistent and repeatable. The LTC2605-1/
LTC2615-1/LTC2625-1 set the voltage outputs to mid-scale
when power is rst applied.
For some applications, downstream circuits are active dur-
ing DAC power-up, and may be sensitive to nonzero outputs
from the DAC during this time. The LTC2605/LTC2615/
LTC2625 contain circuitry to reduce the power-on glitch:
the analog outputs typically rise less than 10mV above
zero-scale during power on if the power supply is ramped
to 5V in 1ms or more. In general, the glitch amplitude
decreases as the power supply ramp time is increased.
See Power-On Reset Glitch in the Typical Performance
Characteristics section.
Power Supply Sequencing
The voltage at REF (Pin 6) should be kept within the range
–0.3V ≤ VREF ≤ VCC + 0.3V (see Absolute Maximum Rat-
ings). Particular care should be taken to observe these
limits during power supply turn-on and turn-off sequences,
when the voltage at VCC (Pin 16) is in transition.
Transfer Function
The digital-to-analog transfer function is:
V
k
V
OUT IDEAL
N
REF
() =
2
where k is the decimal equivalent of the binary DAC input
code, N is the resolution and VREF is the voltage at REF
(Pin 6).
Serial Digital Interface
The LTC2605/LTC2615/LTC2625 communicate with a
host using the standard 2-wire digital interface. The Tim-
ing Diagram (Figure 1) shows the timing relationship of
the signals on the bus. The two bus lines, SDA and SCL,
must be high when the bus is not in use. External pull-up
resistors or current sources are required on these lines.
The value of these pull-up resistors is dependent on the
power supply and can be obtained from the I2C specica-
tions. For an I2C bus operating in the fast mode, an active
pull-up will be necessary if the bus capacitance is greater
than 200pF. The VCC power should not be removed from
the LTC2605/LTC2615/LTC2625 when the I2C bus is active
to avoid loading the I2C bus lines through the internal ESD
protection diodes.
The LTC2605/LTC2615/LTC2625 are receive-only (slave)
devices. The master can write to the LTC2605/LTC2615/
LTC2625. The LTC2605/LTC2615/LTC2625 do not respond
to a read from the master.
The START (S) and STOP (P) Conditions
When the bus is not in use, both SCL and SDA must be
high. A bus master signals the beginning of a communica-
tion to a slave device by transmitting a START condition. A
START condition is generated by transitioning SDA from
high to low while SCL is high.
Table 1
COMMAND*
C3
C2
C1
C0
0
Write to Input Register n
0
1
Update (Power Up) DAC Register n
0
1
0
Write to Input Register n, Update (Power Up) All n
0
1
Write to and Update (Power Up) n
0
1
0
Power Down n
1
No Operation
*Address and command codes not shown are reserved and should not
be used.
ADDRESS (n)*
A3
A2
A1
A0
0
DAC A
0
1
DAC B
0
1
0
DAC C
0
1
DAC D
0
1
0
DAC E
0
1
0
1
DAC F
0
1
0
DAC G
0
1
DAC H
1
All DACs
相關PDF資料 |
PDF描述 |
|---|---|
| NRS6028T330MMGJ | INDUCTOR POWER 33UH 1.1A SMD |
| RP40-4812DGW-HC | CONV DC/DC 40W 18-75VIN +/-12V |
| DC812A | BOARD DAC LTC2606 |
| EMC07DRTI-S13 | CONN EDGECARD 14POS .100 EXTEND |
| UCS2G560MND9 | CAP ALUM 56UF 400V 20% RADIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC935KB-GB | 制造商:DEWALT 功能描述:DRILL 14.4V |
| DC9360 | 制造商:Dewalt 功能描述:36 Volt Li-Ion Replacement Battery for DeWalt |
| DC936A | 功能描述:BOARD DAC LTC2609 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:QuikEval™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| DC939A | 功能描述:BOARD DELTA SIGMA ADC LTC2484 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:Easy Drive™, QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC940KB-GB | 制造商:DEWALT 功能描述:DRILL 12V |
發布緊急采購，3分鐘左右您將得到回復。