- 您現在的位置：買賣IC網 > PDF目錄17064 > DC1009A-B (Linear Technology)BOARD DELTA SIGMA ADC LTC2488 PDF資料下載
參數資料
| 型號： | DC1009A-B |
| 廠商： | Linear Technology |
| 文件頁數： | 16/30頁 |
| 文件大小： | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2488 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC1009A Design File DC1009A Schematic |
| 標準包裝： | 1 |
| 系列： | Easy Drive™, QuikEval™ |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 6.9 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 已用 IC / 零件： | LTC2488 |
| 已供物品： | 板 |
| 相關產品： | LTC2488CDE#TRPBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2488IDE#TRPBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2488CDE#PBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2488IDE#PBF-ND - IC ADC 16BIT DELTA SIG 14-DFN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
LTC2488
23
2488fa
APPLICATIONS INFORMATION
IN– are matched. Mismatches in source impedance lead
to a xed offset error but do not effect the linearity or full
scale reading. A 1% mismatch in a 1k source resistance
leads to a 74μV shift in offset voltage.
In applications where the common mode input voltage
varies as a function of the input signal level (single ended
type sensors), the common mode input current varies
proportionally with input voltage. For the case of balanced
input impedances, the common mode input current effects
are rejected by the large CMRR of the LTC2488, leading
to little degradation in accuracy. Mismatches in source
impedances lead to gain errors proportional to the dif-
ference between the common mode input and common
mode reference. 1% mismatches in 1k source resistances
lead to gain errors on the order of 15ppm. Based on the
stability of the internal sampling capacitors and the ac-
curacy of the internal oscillator, a one-time calibration will
remove this error.
In addition to the input sampling current, the input ESD
protection diodes have a temperature dependent leakage
current. This current, nominally 1nA (±10nA Max), results
in a small offset shift. A 1k source resistance will create a
1μV typical and a 10μV maximum offset voltage.
Reference Current
Similar to the analog inputs, the LTC2488 samples the
differential reference pins (REF+ and REF–) transferring
small amounts of charge to and from these pins, thus
producing a dynamic reference current. If incomplete set-
tling occurs (as a function the reference source resistance
and reference bypass capacitance) linearity and gain errors
are introduced.
For relatively small values of external reference capacitance
(CREF < 1nF), the voltage on the sampling capacitor settles
for reference impedances of many kΩ (if CREF = 100pF up
to 10kΩ will not degrade the performance) (see Figures
11 and 12).
In cases where large bypass capacitors are required on
the reference inputs (CREF > 0.01μF) full-scale and linear-
ity errors are proportional to the value of the reference
resistance. Every ohm of reference resistance produces
a full-scale error of approximately 0.5ppm (while operat-
ing with the internal oscillator) (see Figures 13 and 14). If
the input common mode voltage is equal to the reference
common mode voltage, a linearity error of approximately
0.67ppm per 100Ω of reference resistance results (see
Figure 15). In applications where the input and reference
common mode voltages are different, the errors increase.
A 1V difference in between common mode input and
common mode reference results in a 6.7ppm INL error
for every 100Ω of reference resistance.
In addition to the reference sampling charge, the reference
ESD protection diodes have a temperature dependent leak-
age current. This leakage current, nominally 1nA (±10nA
max) results in a small gain error. A 100Ω reference
resistance will create a 0.5μV full scale error.
Figure 11. +FS Error vs RSOURCE at VREF (Small CREF)
Figure 12. –FS Error vs RSOURCE at VREF (Small CREF)
RSOURCE (Ω)
0
+FS
ERROR
(ppm)
50
70
90
10k
2488 F11
30
10
40
60
80
20
0
–10
10
100
1k
100k
VCC = 5V
VREF = 5V
VIN
+ = 3.75V
VIN
– = 1.25V
FO = GND
TA = 25°C
CREF = 0.01μF
CREF = 0.001μF
CREF = 100pF
CREF = 0pF
RSOURCE (Ω)
0
–FS
ERROR
(ppm) –30
–10
10
10k
2488 F12
–50
–70
–40
–20
0
–60
–80
–90
10
100
1k
100k
VCC = 5V
VREF = 5V
VIN
+ = 1.25V
VIN
– = 3.75V
FO = GND
TA = 25°C
CREF = 0.01μF
CREF = 0.001μF
CREF = 100pF
CREF = 0pF
相關PDF資料 |
PDF描述 |
|---|---|
| AD9787-DPG2-EBZ | BOARD EVALUATION FOR AD9787 |
| ESA10DTKS | CONN EDGECARD 20POS DIP .125 SLD |
| SDR0604-331KL | INDUCTOR POWER 330UH 10% SMD |
| AD9788-DPG2-EBZ | BOARD EVALUATION FOR AD9788 |
| SLPX223M025E7P3 | CAP ALUM 22000UF 25V 20% SNAP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC1009A-C | 功能描述:BOARD DELTA SIGMA ADC LTC2486 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:Easy Drive™, QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC100A10 | 功能描述:固態繼電器-工業安裝 SSR DC OUTPUT 10A 90-140VAC RoHS:否 制造商:Crydom 控制電壓范圍:4 VDC to 32 VDC 負載電壓額定值:7 VDC to 72 VDC 負載電流額定值:160 A 觸點形式: 輸出設備:SSR 安裝風格:Panel |
| DC100A10C | 功能描述:固態繼電器-工業安裝 SSR DC OUTPUT 10A 90-140VAC RoHS:否 制造商:Crydom 控制電壓范圍:4 VDC to 32 VDC 負載電壓額定值:7 VDC to 72 VDC 負載電流額定值:160 A 觸點形式: 輸出設備:SSR 安裝風格:Panel |
| DC100A20 | 功能描述:固態繼電器-工業安裝 SSR DC OUTPUT 20A 90-140VAC RoHS:否 制造商:Crydom 控制電壓范圍:4 VDC to 32 VDC 負載電壓額定值:7 VDC to 72 VDC 負載電流額定值:160 A 觸點形式: 輸出設備:SSR 安裝風格:Panel |
| DC100A20C | 功能描述:固態繼電器-工業安裝 SSR DC OUTPUT 20A 90-140VAC RoHS:否 制造商:Crydom 控制電壓范圍:4 VDC to 32 VDC 負載電壓額定值:7 VDC to 72 VDC 負載電流額定值:160 A 觸點形式: 輸出設備:SSR 安裝風格:Panel |
發布緊急采購，3分鐘左右您將得到回復。