- 您現在的位置：買賣IC網 > PDF目錄1992 > DAC8426EPZ (Analog Devices Inc)IC DAC 8BIT QUAD 10VREF 20PDIP PDF資料下載
參數資料
| 型號： | DAC8426EPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 12/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 8BIT QUAD 10VREF 20PDIP |
| 標準包裝： | 18 |
| 設置時間： | 3µs |
| 位數： | 8 |
| 轉換器數目： | 4 |
| 電壓電源： | 雙 ± |
| 功率耗散（最大）： | 210mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 20-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 20-PDIP |
| 包裝： | 管件 |
| 輸出數目和類型： | 4 電流，單極；4 電流，雙極 |
| 采樣率（每秒）： | 333k |
DAC8426
–9–
REV. C
APPLICATIONS SETUP
UNIPOLAR OUTPUT OPERATION
The output voltage appearing at any output VOUT is equal to the
internal 10 V reference multiplied by the decimal value of the
latched digital input divided by 2
8 (= 256). In equation form:
VOUT(D) = D/256 × 10 V
where D = 010 to 25510
Figure 4. Amplifier Output Stage
Note that the maximum possible output is 1 LSB less than the
internal 10 V reference, that is, 255/256
× 10 V = 9.961 V.
Table II lists output voltages for a given digital input. The total
unadjusted error (TUE) specification of the product grade used
determines the output tolerances of the values listed in Table II.
For example, a
±2 LSB grade DAC8426FP loaded with decimal
12810 (half-scale) would have a guaranteed output voltage oc-
curring in the range of 5 V
±2 LSB, which is 5 V ±(2 × 10 V/256)
= 5 V
±0.078 V. Therefore V
OUT is guaranteed to occur in the
following range:
4.922 V
≤ V
OUT(128) ≤ 5.078 V
Figure 5. DAC Output Current Sink
For the top grade DAC8426EP
±1 LSB total unadjusted error
(TUE), the guaranteed range is 4.961 V
≤ V
OUT (12810)
≤ 5.039 V.
These tolerances provide the worst case analysis including tem-
perature changes.
One additional characteristic guaranteed is a DNL of
±1 LSB
on all grades. The DAC8426 is therefore guaranteed to be mon-
otonic. In the situation where a continuously positive 1 LSB
digital increment is applied, the output voltage will always in-
crease in value, never decrease. This is very important is servo
applications and other closed-loop feedback systems. Finally, in
the typical characteristic curves, long term output voltage drift
(stability) is provided.
BIPOLAR OUTPUT OPERATION
An external op amp plus two resistors can easily convert any
DAC output to bipolar output voltage swings. Figure 6 shows all
four DACs output operating in bipolar mode. This is the general
expression describing the bipolar output transfer equation:
VOUT(D) = [(1 +R2/R1) × D/256 × 10 V] –R2/R1 × 10 V,
where D = 010 to 25510
If R1 = R2, then VOUT becomes:
VOUT (D) = (D/128–1) × 10 V
Table III lists various output voltages with R1 = R2 versus digital
input code. This coding is considered offset binary. Note that
the LSB step size is now 20 V/256 = 0.078 V, twice as large as
the unipolar output case previously discussed. In order to minimize
gain and offset errors, choose R1 and R2 to match and track
within 0.1% over the selected operating temperature range
of interest.
Table II. Unipolar Output Voltage as a Function of
Digital Input Code
Digital Input
Analog Output
Code
Voltage (= D/256
× 10 V)
255
9.961 V
Full-Scale (FS)
254
9.922 V
FS-1 LSB
129
5.039 V
128
5.000 V
Half-Scale
127
4.961 V
1
0.039 V
1 LSB
0
0.000 V
Zero-Scale
OFFSETTING AGND
Since the DAC ladder and bandgap reference are terminated at
AGND, it is possible to offset AGND positive with respect to
DGND. The 10 V output span remains if a positive offset is ap-
plied to AGND. The offset voltage source connected to AGND
must be capable of sinking 14 mA. AGND cannot be taken
negative with respect to DGND; this would forward bias an in-
ternal diode. Allowance must be made at VDD to maintain 3.5 V
of headroom above VREFOUT. This connection setup is useful
in single supply applications where virtual ground needs to be
slightly positive with respect to ground. In this application con-
nect VSS to DGND to take advantage of the extra buffer output
current sinking capability when the DAC output is programmed
to all zeros code, see Figure 7.
相關PDF資料 |
PDF描述 |
|---|---|
| DAC8531IDRBTG4 | IC D/A CONV LP 16-BIT 8-SON |
| DAC8562FP | IC DAC 12BIT PARALLEL 5V 20-DIP |
| DS1004Z-5+T | IC DELAY LINE 5TAP 25NS 8-SOIC |
| DS1005-125+ | IC DELAY LINE 5TAP 125NS 14-DIP |
| DS1007S-2+T&R | IC DELAY LINE 4NS 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC8426ER | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad 8-Bit Voltage Out CMOS DAC Complete with Internal 10 V Reference |
| DAC8426FP | 功能描述:IC DAC 8BIT QUAD 10VREF 20-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| DAC8426FPZ | 功能描述:IC DAC 8BIT QUAD 10VREF 20DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| DAC8426FR | 制造商:Rochester Electronics LLC 功能描述:COMPLETE QUAD CMOS 8-BIT - Bulk 制造商:Analog Devices 功能描述: |
| DAC8426FS | 功能描述:IC DAC 8BIT QUAD W/V-REF 20-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。