- 您現在的位置：買賣IC網 > PDF目錄237684 > D2F-01FL2-A1 SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.1A, 30VDC, 0.55mm, THROUGH HOLE-RIGHT ANGLE PDF資料下載
參數資料
| 型號： | D2F-01FL2-A1 |
| 元件分類： | 開關 |
| 英文描述： | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.1A, 30VDC, 0.55mm, THROUGH HOLE-RIGHT ANGLE |
| 封裝： | ROHS COMPLIANT |
| 文件頁數： | 2/12頁 |
| 文件大?。?/td> | 277K |
| 代理商： | D2F-01FL2-A1 |
General Information
General Information
29
Snap-back
Incorrect
Correct
Shock operation
Make sure that no improper force is applied to the actuator,
otherwise the actuator may incur local abrasion. As a result, the
actuator may become damaged or its durability may be
deteriorated.
Dog
Roller
Incorrect
Correct
Operating
body
Operating
body
: Correct
: Incorrect
Make sure that the operating body moves in a direction where
the actuator moves. If the actuator is a pin plunger type, make
sure that the operating body presses the pin plunger vertically.
Operate the actuator of a hinge roller lever or simulated hinge
lever type in the direction shown below.
Incorrect
Correct
Set the angle of the cam or dog (θ) for roller levers and similar
actuators to the range between 30
_ and 45_. If the angle is too
large, an abnormally large horizontal stress will be applied to the
lever.
Do not modify the actuator. If the actuator is modified, excessive
external force may be applied to the internal switch mechanism,
characteristics may change, and the switch may stop
functioning.
If an external actuator is used as an operating object, check the
material and thickness of the lever to make sure that the force
applied to the lever is within the permissible range.
Mounting
Securing
When mounting a switch, be sure to use the specified mounting
screws and tighten the screws with flat washers or spring washers
securely.
However, the switch housing may incur crack damage if it comes
into contact with the spring washers directly. In that case make sure
that the flat washers come into contact with the switch housing as
shown below. Do not subject the switch to excessive shock or high-
frequency vibrations when mounting (e.g., do not use an impact
driver) as it may cause contacts stick or switch damage.
Screw
Flat washer
Spring washer
Resin
Incorrect
Correct
Do not modify the switch in any way, for example, by widening the
mounting holes.
Locking Agent
If glue or locking agent is applied, make sure that it does not stick to
the moving parts or intrude into the inside of the switch, otherwise
the switch may have operating failure or contact failure. Some types
of glue or locking agent may generate gas that has a bad influence
on the switch. Pay the utmost attention when selecting glue or lock-
ing agent.
Wiring
Make sure that the lead wires are connected with no inappropriate
pulling force.
Mounting Location
Be sure not to mount a switch in locations where the switch may be
actuated by mistake.
Maintenance and Inspection
Make sure that a switch is mounted in locations that allow easy
inspection or replacement of the switch.
Mounting Direction
When using a switch with a low operating force mounted with a long
lever, make sure that the switch is mounted in the direction where
the weight of the lever is not applied to the pushbutton directly,
otherwise the switch may have releasing failures.
Terminal Connections
Solder Terminals
When soldering lead wires to a switch, make sure that the tempera-
ture of the iron tip is 380
°C maximum. Improper soldering may
cause abnormal heat radiation from the switch and the switch may
burn.
Complete soldering within 5 seconds at 350
°C or within 3 seconds
at 380
°C. If heat is applied for longer period of time, switch charac-
teristics will be deteriorated, e.g., the case will melt and lead wire
insulation will scorch.
Soldering conditions are even more strict for ultra subminiature
switches. Refer to the Precautions for individual models for details.
Quick-Connect Terminals
Use the specified receptacles to connect to quick-connect termi-
nals. Do not apply excessive force horizontally or vertically to the
相關PDF資料 |
PDF描述 |
|---|---|
| D2SW-P2L3D | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 2A, 30VDC, 0.8mm, THROUGH HOLE-STRAIGHT |
| D372-W9LL | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 12.8mm, PANEL MOUNT |
| D373-Q3AA | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 2.7mm, PANEL MOUNT |
| DHS8SR/TC | SLIDE DIP SWITCH-8SWITCHES, SPST, LATCHED,0.1A, 6VDC, SURFACE MOUNT-STRAIGHT |
| D368-S8KA | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 4.4mm, PANEL MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| D2F01FL2D | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT HINGE ER LVR SLDR 0.1A 30VDC 0.74N SCRW M - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH SPDT .1A 40GF SOLDER 制造商:Omron Electronic Components LLC 功能描述:Switch Snap Action N.O./N.C. SPDT Hinge Roller Lever Solder 0.1A 30VDC 0.39N Screw Mount |
| D2F-01FL2-D | 功能描述:基本/快動開關 Subminiature Basic Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
| D2F-01FL2-D3 | 制造商:OMRON 制造商全稱:Omron Electronics LLC 功能描述:Snap Action Switch |
| D2F-01FL2-T | 制造商:OMRON 制造商全稱:Omron Electronics LLC 功能描述:Snap Action Switch |
| D2F01FL3 | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT SIMULATED ER LVR PC PINS 0.1A 30VDC 0.74N - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH SPDT .1A 40GF PCB 制造商:Omron Electronic Components LLC 功能描述:MICROSWITCH SIM ROLLER 0.1 制造商:Omron Electronic Components LLC 功能描述:MICROSWITCH, SIM ROLLER, 0.1 制造商:Omron Electronic Components LLC 功能描述:Switch,sim-roller lever,75gf,PCB tm,0.1A 制造商:Omron Electronic Components LLC 功能描述:Switch Snap Action N.O./N.C. SPDT Simulated Roller Lever PC Pins 0.1A 30VDC 0.39N Thru-Hole 制造商:Omron 功能描述:Switch Snap Action N.O./N.C. SPDT Simulated Roller Lever PC Pins 0.1A 30VDC 0.39N Thru-Hole |
發布緊急采購，3分鐘左右您將得到回復。