參數資料
型號: CSP1027
元件分類: Codec
英文描述: CSP1027 Voice Band Codec for Cellular Handset and Modem Applications
中文描述: CSP1027語音頻帶編解碼器的蜂窩手機和調制解調器應用
文件頁數: 41/64頁
文件大?。?/td> 937K
代理商: CSP1027
Lucent Technologies Inc.
Data Sheet
December 1999
CSP1027 Voice Band Codec for
Cellular Handset and Modem Applications
41
7 Application Information
(continued)
7.4.3 Printed-Circuit Board Layout Considerations
The following guidelines should be followed when designing the printed-circuit board layout for a crystal-based
application:
1. Keep crystal and external capacitors as close to XLO and XHI pins as possible to minimize board stray capaci-
tance.
2. Keep high-frequency digital signals such as CKO1 and CKO2 away from XLO and XHI traces to avoid coupling
into the oscillator.
7.4.4 LC Network Design for Third Overtone Crystal Circuits
For operating frequencies of greater than 30 MHz, it is usually cost advantageous to use a third overtone crystal as
opposed to a fundamental mode crystal. When using third overtone crystals, it is necessary, however, to filter out
the fundamental frequency so that the circuit will oscillate only at the third overtone. There are several techniques
that will accomplish this; one of these is described below.
Figure 35 shows the basic setup for third overtone operation.
Figure 35. Third Overtone Crystal Configuration
The parallel combination of L
1
and C
1
forms a resonant circuit with a resonant frequency between the first and third
harmonic of the crystal such that the LC network appears inductive at the fundamental frequency and capacitive at
the third harmonic. This ensures that a 360
°
phase shift around the oscillator loop will occur at the third overtone
frequency but not at the fundamental. The blocking capacitor, C
3
, provides dc isolation for the trap circuit and
should be chosen to be large compared to C
1
.
For example, suppose it is desired to operate with a 40 MHz, third overtone, crystal.
Let:
f
3
= operating frequency of third overtone crystal (40 MHz in this example)
f
1
= fundamental frequency of third overtone crystal, or f
3
/3 (13.3 MHz in this example)
2
π
L1C1
f
T
= resonant frequency of trap =
C
2
= external load capacitor (10 pF in this example)
C
3
= dc blocking capacitor (0.1 μF in this example)
XLO
XHI
XTAL
C
1
C
2
C
3
L
1
5-7614 (F)
--------------------------
相關PDF資料
PDF描述
CT1469-2 CT1469-2 MIL-STD-1397 Type E 10MHz Transceiver
CT1496-2 CT1496-2 MIL-STD-1397 Type E 10MHz Low Level Serial Manchester 32 Bit Encoder
CT1508-2 CT1508-2 MIL-STD-1397 Type E 10MHz Serial Manchester 4-Bit SIS / SOS Decoder
CT1611 DMA Controller with Buffer Memory,MIL-STD-1750A Compatible
CT1611-FP DMA Controller with Buffer Memory,MIL-STD-1750A Compatible
相關代理商/技術參數
參數描述
CSP1027J 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC
CSP1027-J11-DB 制造商:Alcatel-Lucent 功能描述:
CSP1027S 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC
CSP1027-S11-DB 制造商:Rochester Electronics LLC 功能描述:- Bulk
CSP1034AH 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC