- 您現在的位置：買賣IC網 > PDF目錄382919 > CS8371ETHA7 THREE-TERMINAL POSITIVE FIXED VOLTAGE REGULATORS PDF資料下載
參數資料
| 型號： | CS8371ETHA7 |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | THREE-TERMINAL POSITIVE FIXED VOLTAGE REGULATORS |
| 中文描述： | 三端固定電壓調節器 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 99K |
| 代理商： | CS8371ETHA7 |
CS8371
http://onsemi.com
8
DEFINITION OF TERMS
Dropout Voltage
– The input–output voltage differential
at which the circuit ceases to regulate against further
reduction in input voltage. Measured when the output
voltage has dropped 100 mV from the nominal value
obtained at 14 V input, dropout voltage is dependent upon
load current and junction temperature.
Current Limit
– Peak current that can be delivered to the
output.
Input Voltage
– The DC voltage applied to the input
terminals with respect to ground.
Input Output Differential
– The voltage difference
between the unregulated input voltage and the regulated
output voltage for which the regulator will operate.
Line Regulation
– The change in output voltage for a
change in the input voltage. The measurement is made under
conditions of low dissipation or by using pulse techniques
such that the average chip temperature is not significantly
affected.
Load Regulation
– The change in output voltage for a
change in load current at constant chip temperature.
Long Term Stability
– Output voltage stability under
accelerated life–test conditions after 1000 hours with
maximum rated voltage and junction temperature.
Output Noise Voltage
– The rms AC voltage at the
output, with constant load and no input ripple, measured
over a specified frequency range.
Quiescent Current
– The part of the positive input
current that does not contribute to the positive load current.
The regulator ground lead current.
Ripple Rejection
– The ratio of the peak–to–peak input
ripple voltage to the peak–to–peak output ripple voltage.
Temperature Stability of V
OUT
– The percentage
change in output voltage for a thermal variation from room
temperature to either temperature extreme.
Figure 23. Applications Circuit
V
IN
GND
ENABLE
1
V
OUT1
V
OUT2
C
Tuner IC
Control
C
1
*
0.1
μ
F
5.0 V
8.0 V
* C
1
is required if the regulator is far from the power source filter.
ENABLE
2
APPLICATION NOTES
With seperate control of each output channel, the CS8371
is ideal for applications where each load must be switched
independently. In an automotive radio, the 8.0 V output
drives the displays and tape drive motors while the 5.0 V
output supplies the Tuner IC and memory.
Stability Considerations/NOCAP
Normally a low dropout or quasi–low dropout regulator
(or any type requiring a slow lateral PNP in the control loop)
necessitates a large external compensation capacitor at the
output of the IC. The external capacitor is also used to curtail
overshoot, determine startup delay time and load transient
response.
Traditional LDO regulators typically have low unity gain
bandwidth, display overshoot and poor ripple rejection.
Compensation is also an issue because the high frequency
load capacitor value, ESR (Equivalent Series Resistance)
and board layout parasitics all can create oscillations if not
properly accounted for.
NOCAP is an ON Semiconductor exclusive output stage
which internally compensates the LDO regulator over
temperature, load and line variations without the need for
an expensive external capacitor. It incorporates high gain
(>80 dB) and large unity gain bandwidth (>100 kHz) while
maintaining many of the characteristics of a single–pole
amplifier (large phase margin and no overshoot).
NOCAP is ideally suited for slow switching or steady
loads. If the load displays large transient current
requirements, such as with high frequency microprocessors,
an output storage capacitor may be needed. Some large
capacitor and small capacitor ESR values at the output may
相關PDF資料 |
PDF描述 |
|---|---|
| CS83C92A-CL | LAN Transceiver |
| CS83C92A-CP | LAN Transceiver |
| CS83C92C-CL | LAN Transceiver |
| CS83C92C-CP | LAN Transceiver |
| CS8441YN8 | Stepper Motor Controller/Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS8371ETVA7 | 功能描述:線性穩壓器 - 標準 8V/1A 5V/250mA Dual RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| CS8371ETVA7G | 功能描述:線性穩壓器 - 標準 8V/1A 5V/250mA Dual Micropower w/ENABLE RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| CS8375 | 制造商:Hubbell Premise Wiring 功能描述:Conn Inlets M 3Power/1Ground POS ST Flange Mount 4 Terminal 1 Port 制造商:Woodhead Molex 功能描述:Conn Power PL 3Power/1Ground POS ST Flange Mount 4 Terminal 1 Port 制造商:Hubbell Wiring Device-Kellems 功能描述:Conn Inlets M 3Power/1Ground POS ST Flange Mount 4 Terminal 1 Port |
| CS837-5 | 制造商:Leviton Manufacturing Co 功能描述: |
| CS8375L | 制造商:Hubbell Wiring Device-Kellems 功能描述:LKG INLT, 50A 3P250V, 3P4W, LC |
發布緊急采購，3分鐘左右您將得到回復。