- 您現在的位置：買賣IC網 > PDF目錄374169 > CS5208-1 (ZF Electronics Corporation) 8A LDO 3-Pin Adjustable Linear Regulator PDF資料下載
參數資料
| 型號： | CS5208-1 |
| 廠商： | ZF Electronics Corporation |
| 英文描述： | 8A LDO 3-Pin Adjustable Linear Regulator |
| 中文描述： | 8A條LDO的3引腳可調線性穩壓器 |
| 文件頁數： | 6/7頁 |
| 文件大?。?/td> | 136K |
| 代理商： | CS5208-1 |
6
C
ed to ground, damage can occur. In this case, a diode con-
nected as shown in Figure 3 is recommended.
A rule of thumb useful in determining if a protection diode
is required is to solve for current
I =
, where
I is the current flow out of the load capacitance when
V
IN
is shorted,
C is the value of the load capacitance,
V is the output voltage, and
T is the time duration required for V
IN
to transition
from high to being shorted.
If the calculated current is greater than or equal to the typi-
cal short circuit current value provided in the specifica-
tions, serious thought should be given to including a pro-
tection diode.
Figure 3.
Current Limit
The internal current limit circuit limits the output current
under excessive load conditions and protects the regulator.
Short Circuit Protection
The device includes foldback short circuit current limit that
clamps the output current at approximately two amperes
less than its current limit value.
Thermal Shutdown
The thermal shutdown circuitry is guaranteed by design to
become activated above a die junction temperature of
150C and to shut down the regulator output. This circuit-
ry includes a thermal hysteresis circuit with 25C of typical
hysteresis, thereby allowing the regulator to recover from a
thermal fault automatically.
Calculating Power Dissipation and Heat Sink
Requirements
High power regulators such as the CS5208-1 usually oper-
ate at high junction temperatures. Therefore, it is important
to calculate the power dissipation and junction tempera-
tures accurately to ensure that an adequate heat sink is
used. Since the package tab is connected to Vout on the
CS5208-1, electrical isolation may be required for some
applications. Also, as with all high power packages, ther-
mal compound in necessary to ensure proper heat flow.
For added safety, this high current LDO includes an inter-
nal thermal shutdown circuit
The thermal characteristics of an IC depend on the follow-
ing four factors. Junction temperature, ambient tempera-
ture, die power dissipation, and the thermal resistance
from the die junction to ambient air. The maximum junc-
tion temperature can be determined by:
T
J(max)
= T
A(max)
+ P
D(max)
′
R
Q
JA
The maximum ambient temperature and the power dissi-
pation are determined by the design while the maximum
junction temperature and the thermal resistance depend on
the manufacturer and the package type. The maximum
power dissipation for a regulator is:
PD
(max)
= (V
IN(max)
-V
OUT(min)
)I
OUT(max)
+ V
IN(max)
′
I
IN(max)
A heat sink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air. Each material in the heat flow
path between the IC and the outside environment has a
thermal resistance which is measured in degrees per watt.
Like series electrical resistances, these thermal resistances
are summed to determine the total thermal resistance
between the die junction and the surrounding air, R
Q
JA
.
This total thermal resistance is comprised of three compo-
nents. These resistive terms are measured from junction to
case (R
Q
JC
), case to heat sink (R
Q
CS
), and heat sink to ambi-
ent air (R
Q
SA
). The equation is:
R
Q
JA
= R
Q
JC
+ R
Q
CS
+ R
Q
SA
R
Q
JC
is rated @ 1.4C/W for the CS5208-1. For a high cur-
rent regulator such as the CS5208-1 the majority of heat is
generated in the power transistor section. The value for
R
Q
SA
depends on the heat sink type, while the R
Q
CS
depends on factors such as package type, heat sink inter-
face (is an insulator and thermal grease used), and the
contact area between the heat sink and the package. Once
these calculations are complete, the maximum permissible
value of R
JA
can be calculated and the proper heat sink
selected. For further discussion on heat sink selection, see
our Cherry application note òThermal Management for
Linear Regulators.ó
V
OUT
V
IN
CS5208-1
Adj
C
′
V
T
Application Notes: continued
相關PDF資料 |
PDF描述 |
|---|---|
| CS5253-1 | 3A LDO 5-Pin Adjustable Linear Regulator |
| CS5253-1GDP5 | 3A LDO 5-Pin Adjustable Linear Regulator |
| CS5253-1GDPR5 | 3A LDO 5-Pin Adjustable Linear Regulator |
| CS5257A-1 | 7A LDO 5-Pin Adjustable Linear Regulator |
| CS5257A-1GDP5 | 7A LDO 5-Pin Adjustable Linear Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS5208-1/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8A LDO 3-Pin Adjustable Linear Regulator |
| CS5208-1GT3 | 功能描述:IC REG LDO ADJ 8A TO220-3 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓撲結構:正，固定式和可調式 輸出電壓:3.3V，1.25 V ~ 5.7 V 輸入電壓:4.5 V ~ 7 V 電壓 - 壓降（標準）:1.1V @ 1A 穩壓器數量:2 電流 - 輸出:1A 電流 - 限制（最?。?1A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-252-5，DPak（4 引線 + 接片），TO-252AD 供應商設備封裝:PPAK 包裝:管件 其它名稱:497-3576-5 |
| CS-5208-1T3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Positive Adjustable Voltage Regulator |
| CS-5208A-1T3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Positive Adjustable Voltage Regulator |
| CS5210-1 | 制造商:CHERRY 制造商全稱:CHERRY 功能描述:10A LDO 3-Pin Adjustable Linear Regulator |
發布緊急采購，3分鐘左右您將得到回復。